Page 12 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57179
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
E*$$"83%,89%G*#$"83
GI%JK6!6MG%E6KLIPE%LMjPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
N,X*%#'(*%$.,$%$.*%G("33*(%"#%"8%$.*%&22?/&#"$"&8%,89%'8/7'3%$.*%$&&7%2(&5%"$#%
*7*4$("4,7%&'$7*$%+*2&(*%/*(2&(5"83%,8V%/(&4*9'(*%"8%$."#%#*4$"&81
F9]'#$"83%$.*%N"$*(%F837*
A miter cut is one that is at an angle across the
horizontal surface of the material. 45º miter
cuts to join two pieces in a right angle corner
are common. A 30º cut is often used for a
scarf joint or to make a chamfered end.
1. Pull up on the Miter Lock Handle to unlock the
Table. Push down on the Miter Latch Lever
and move the Table to the desired angle.
2. The Miter Angle Indicator will indicate the selected
angle. When the Miter Latch Lever is released,
the Table will lock into place at often used miter
angles, including 0º, 15º, 22.5º, 31.6º, and 45º
left and 0º, 15º, 22.5º, 31.6º, 45º, and 60º right.
3. To override the pre-set detents (stops) for micro
adjustments at any angle, push down and hold
the Miter Latch Lever and push in on the Detent
Latch Button to latch in place. Release the Miter
Latch Lever and adjust Table to any position on the
miter scale. To disengage push down on the Miter
Latch Lever to release the Detent Latch Button.
N"$*(%T,$4.%
T*W*(
N"$*(%
T&4X%
_,897*
U*$*8$%
T,$4.%
S'$$&8
;"3'(*%6
4. Push down on the Miter Lock Handle to lock
the Table after adjusting the miter angle.
5. With the Table adjusted to the desired angle,
place the workpiece flush against the Fence,
secure it with the Clamp and make the cut.
F9]'#$"83%$.*%S*W*7%F837*
A bevel cut is one that is at an angle vertically. Bevel
cuts can be used to miter relatively wide and thin
material. Bevel cuts can be used in combination with
a miter cut to form a compound angle. Compound
angle cuts are often used in crown moldings,
picture frames and similar trim materials.
1. Pull up on the Bevel Lock Handle to
unlock the Saw Head Assembly.
2. To adjust the left bevel angle, move the Saw Head
Assembly to the left to the desired angle. Read
the angle on the Bevel Scale. To adjust the right
bevel angle, pull out the Bevel Angle Lock Button
at the rear of the Saw and move the Saw Head
Assembly to the right to the desired angle.
3. Lock the Saw Head Assembly into position by
pushing down on the Bevel Lock Handle.
4. Make a sample cut in a piece of scrap to
confirm that the bevel angle is correct.
If it is not, correct the angle before cutting.
QFKMLMRi%%GI%JK6!6MG%E6KLIPE%LMjPKH-%%
F9]'#$%+&$.%#"9*#%&2%$.*%;*84*%47*,(%&2%$.*%S7,9*^#%
4'$$"83%/,$.%,2$*(%5,X"83%,8V%,9]'#$5*8$%$&%$.*%
4'$$"83%,837*1%%N&W*%$.*%S7,9*%$.(&'3.%"$#%2'77%
(,83*%&2%5&$"&8%$&%*8#'(*%$.*%;*84*#%,(*%47*,(1
S*W*7%F837*%S*W*7%F837*%
T&4X%S'$$&8T&4X%S'$$&8
S*W*7%T&4X%
_,897*
;"3'(*%;
To Next Page
Loading...
