Mounting the CPU cooler
First remove the protective foil from the underside of the
cooler. Spread the thermal paste on the surface of the CPU.
The amount supplied is sufficient for one or two applications.
Caution: The thermal paste supplied is not suitable for human
consumption. If swallowed, drink lots of water and urgently
seek medical attention. Keep it out of the reach of children.
Avoid contact with skin and eyes.
Position the cooler mounting bridge centrally on the cooler.
Next place the cooler unit onto the CPU. Insert the Intel/
mounting bridge fastening screws from above into the cooler
mounting bridge and then screw these alternately tight. You
can use the cross-tip screwdriver for this.
Mount the 135mm fan onto the cooler unit using the fan
clips. Connect the fan to the motherboard’s PWM signal.
When dismantling the 135mm fan push the notches of the fan
clips away from the fan.
Position the cooler mounting bridge centrally on the cooler.
Next place the cooler unit onto the CPU. Insert the mounting
bridge fastening screws from above into the cooler mounting
bridge and then screw these alternately tight. You can use the
cross-tip screwdriver for this.
Fasten the 135mm fan onto the cooler unit using fan clips.
Connect the fan to the motherboard’s PWM signal.
When dismantling the 135mm fan, push the notches of the
fan clips away from the fan.
Introduction: Thank you for deciding to purchase a be quiet!
product. The following instructions will guide you through the
installation process. If you do encounter installation problems,
please don't hesitate to contact our customer services by
mailing service@bequiet.com. Please note that be quiet!
cannot accept liability for damage caused by compatibility
problems.
Warranty:
• 3 years manufacturer guarantee for consumers (original
purchase from authorized be quiet! dealers only)
• Guarantee work can only be processed with an included
copy of the purchase receipt from an authorized be quiet!
dealer
• Manipulation and structural changes of any kind as well
as damages through external mechanical forces lead to a
complete voiding of the guarantee
• Our General Warranty Conditions apply, which can be
viewed on bequiet.com
Listan GmbH
.
Wilhelm-Bergner-Straße 11c
.
21509 Glinde
Germany
For further information contact us via e-mail:
service@bequiet.com
SCOPE OF DELIVERY
General
We recommend preparatory mounting of the cooler outside
the PC case for subsequent installation.
The following parts are needed for this:
1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 2x Intel
mounting brackets (4), 1x cooler mounting bridge (7), 4x Intel
spacer nut A (8), 4x mounting bracket fastening screws (11), 2x
Mounting bridge fastening screws (12), 1x cross-tip screwdriver
(16) 1x thermal paste (17), 2x fan clips (18)
Assembly of the cooler mounting frame
First screw the Intel spacer nut A onto the threads of the
socket frame. Place the Intel mounting brackets over the Intel
spacer nuts and screw these tight with the mounting bracket
fastening screws. You can use the cross-tip screwdriver for
this.
Mounting the CPU cooler
First remove the protective foil from the underside of the
cooler. Spread the thermal paste on the surface of the CPU.
The amount supplied is sufficient for one or two applications.
Caution: The thermal paste supplied is not suitable for
human consumption. If swallowed, drink lots of water and
urgently seek medical attention. Keep it out of the reach of
children. Avoid contact with skin and eyes.
2011(-3) square ILM, 2066
General
We recommend preparatory mounting of the cooler outside
the PC case for subsequent installation.
The following parts are needed for this:
1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 1x Intel
backplate (3), 2x Intel mounting brackets (4), 1x cooler mounting
bridge (7), 4x Intel spacer nut B (9), 4x mounting bracket fastening
screws (11), 2x mounting bridge fastening screws (12), 4x Intel
backplate screws (13), 4x O-rings (15), 1x cross-tip screwdriver
(16), 1x thermal paste (17), 2x fan clips (18)
Mounting the backplate
Position the Intel backplate screws in the notches situated on
the rear side of the Intel backplate. Pay attention in so doing
to align with the holes drilled for each socket.
For fixing the backplate screws onto the Intel backplate use
the O-rings. Once assembly of the Intel backplate for the
respective Intel socket is complete, position it under the
motherboard. Make sure that the backplate screws are
precisely positioned inside the motherboard holes.
Installation of the mounting brackets
Screw the Intel spacer nut B onto the previously positioned
Intel backplate. Then position the Intel mounting brackets
over the Intel spacer nut B and affix these with the mounting
bracket fastening screws. You can use the cross-tip
screwdriver for this.
1200, 1150, 1151, 1155
Intel: LGA 2011 (-3) square ILM / LGA 2066
Intel: LGA 1200 / 1150 / 1151 / 1155
Part name Quantity
be quiet! Dark Rock 4 cooler 1
135mm fan 1
Intel backplate 1
Intel mounting brackets 2
Long AMD mounting brackets 2
Intel mounting brackets LGA
1700
2
Cooler mounting bridge 1
Intel spacer nut A 4
Part name Quantity
Intel spacer nut B 4
AMD spacer nuts 4
Mounting bracket fastening
screws
4
Mounting bridge fastening
screws
2
Intel backplate screws 4
AMD backplate screws 4
O-rings 4
Cross-tip screwdriver 1
Thermal paste 1
Fan clips 4
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
V1/22
www.bequiet.com/bk021
» Product information for this CPU cooler
» Produktinformationen zu diesem CPU-Kühler
» Informations produit pour ce système de refroidissement
» Información del producto para este refrigerador de CPU
» Informacje produktowe dla tego coolera CPU
» Engelstalige productinformatie voor deze processorkoeler
» Produktinformation för den här processorkylaren, på
engelska
» Подробнаяинформацияоданномкулередля
процессора
» 此CPU散熱器的產品資訊
» 此CPU散热器的产品信息
» 製品情報（クーラー）
NL
SE
18
Mounting the CPU cooler
First remove the protective foil from the underside of the
cooler. Spread the thermal paste on the surface of the CPU.
The amount supplied is sufficient for one or two applications.
Caution: The thermal paste supplied is not suitable for human
consumption. If swallowed, drink lots of water and urgently
seek medical attention. Keep it out of the reach of children.
Avoid contact with skin and eyes.
Position the cooler mounting bridge centrally on the cooler.
Next place the cooler unit onto the CPU. Insert the Intel/
mounting bridge fastening screws from above into the cooler
mounting bridge and then screw these alternately tight. You
can use the cross-tip screwdriver for this.
Mount the 135mm fan onto the cooler unit using the fan
clips. Connect the fan to the motherboard’s PWM signal.
When dismantling the 135mm fan push the notches of the fan
clips away from the fan.
Position the cooler mounting bridge centrally on the cooler.
Next place the cooler unit onto the CPU. Insert the mounting
bridge fastening screws from above into the cooler mounting
bridge and then screw these alternately tight. You can use the
cross-tip screwdriver for this.
Fasten the 135mm fan onto the cooler unit using fan clips.
Connect the fan to the motherboard’s PWM signal.
When dismantling the 135mm fan, push the notches of the
fan clips away from the fan.
Introduction: Thank you for deciding to purchase a be quiet!
product. The following instructions will guide you through the
installation process. If you do encounter installation problems,
please don't hesitate to contact our customer services by
mailing service@bequiet.com. Please note that be quiet!
cannot accept liability for damage caused by compatibility
problems.
Warranty:
• 3 years manufacturer guarantee for consumers (original
purchase from authorized be quiet! dealers only)
• Guarantee work can only be processed with an included
copy of the purchase receipt from an authorized be quiet!
dealer
• Manipulation and structural changes of any kind as well
as damages through external mechanical forces lead to a
complete voiding of the guarantee
• Our General Warranty Conditions apply, which can be
viewed on bequiet.com
Listan GmbH
.
Wilhelm-Bergner-Straße 11c
.
21509 Glinde
Germany
For further information contact us via e-mail:
service@bequiet.com
SCOPE OF DELIVERY
General
We recommend preparatory mounting of the cooler outside
the PC case for subsequent installation.
The following parts are needed for this:
1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 2x Intel
mounting brackets (4), 1x cooler mounting bridge (7), 4x Intel
spacer nut A (8), 4x mounting bracket fastening screws (11), 2x
Mounting bridge fastening screws (12), 1x cross-tip screwdriver
(16) 1x thermal paste (17), 2x fan clips (18)
Assembly of the cooler mounting frame
First screw the Intel spacer nut A onto the threads of the
socket frame. Place the Intel mounting brackets over the Intel
spacer nuts and screw these tight with the mounting bracket
fastening screws. You can use the cross-tip screwdriver for
this.
Mounting the CPU cooler
First remove the protective foil from the underside of the
cooler. Spread the thermal paste on the surface of the CPU.
The amount supplied is sufficient for one or two applications.
Caution: The thermal paste supplied is not suitable for
human consumption. If swallowed, drink lots of water and
urgently seek medical attention. Keep it out of the reach of
children. Avoid contact with skin and eyes.
2011(-3) square ILM, 2066
General
We recommend preparatory mounting of the cooler outside
the PC case for subsequent installation.
The following parts are needed for this:
1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 1x Intel
backplate (3), 2x Intel mounting brackets (4), 1x cooler mounting
bridge (7), 4x Intel spacer nut B (9), 4x mounting bracket fastening
screws (11), 2x mounting bridge fastening screws (12), 4x Intel
backplate screws (13), 4x O-rings (15), 1x cross-tip screwdriver
(16), 1x thermal paste (17), 2x fan clips (18)
Mounting the backplate
Position the Intel backplate screws in the notches situated on
the rear side of the Intel backplate. Pay attention in so doing
to align with the holes drilled for each socket.
For fixing the backplate screws onto the Intel backplate use
the O-rings. Once assembly of the Intel backplate for the
respective Intel socket is complete, position it under the
motherboard. Make sure that the backplate screws are
precisely positioned inside the motherboard holes.
Installation of the mounting brackets
Screw the Intel spacer nut B onto the previously positioned
Intel backplate. Then position the Intel mounting brackets
over the Intel spacer nut B and affix these with the mounting
bracket fastening screws. You can use the cross-tip
screwdriver for this.
1200, 1150, 1151, 1155
Intel: LGA 2011 (-3) square ILM / LGA 2066
Intel: LGA 1200 / 1150 / 1151 / 1155
Part name Quantity
be quiet! Dark Rock 4 cooler 1
135mm fan 1
Intel backplate 1
Intel mounting brackets 2
Long AMD mounting brackets 2
Intel mounting brackets LGA
1700
2
Cooler mounting bridge 1
Intel spacer nut A 4
Part name Quantity
Intel spacer nut B 4
AMD spacer nuts 4
Mounting bracket fastening
screws
4
Mounting bridge fastening
screws
2
Intel backplate screws 4
AMD backplate screws 4
O-rings 4
Cross-tip screwdriver 1
Thermal paste 1
Fan clips 4
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
V1/22
www.bequiet.com/bk021
» Product information for this CPU cooler
» Produktinformationen zu diesem CPU-Kühler
» Informations produit pour ce système de refroidissement
» Información del producto para este refrigerador de CPU
» Informacje produktowe dla tego coolera CPU
» Engelstalige productinformatie voor deze processorkoeler
» Produktinformation för den här processorkylaren, på
engelska
» Подробнаяинформацияоданномкулередля
процессора
» 此CPU散熱器的產品資訊
» 此CPU散热器的产品信息
» 製品情報（クーラー）
NL
SE
18
Mounting the CPU cooler
First remove the protective foil from the underside of the
cooler. Spread the thermal paste on the surface of the CPU.
The amount supplied is sufficient for one or two applications.
Caution: The thermal paste supplied is not suitable for human
consumption. If swallowed, drink lots of water and urgently
seek medical attention. Keep it out of the reach of children.
Avoid contact with skin and eyes.
Position the cooler mounting bridge centrally on the cooler.
Next place the cooler unit onto the CPU. Insert the Intel/
mounting bridge fastening screws from above into the cooler
mounting bridge and then screw these alternately tight. You
can use the cross-tip screwdriver for this.
Mount the 135mm fan onto the cooler unit using the fan
clips. Connect the fan to the motherboard’s PWM signal.
When dismantling the 135mm fan push the notches of the fan
clips away from the fan.
Position the cooler mounting bridge centrally on the cooler.
Next place the cooler unit onto the CPU. Insert the mounting
bridge fastening screws from above into the cooler mounting
bridge and then screw these alternately tight. You can use the
cross-tip screwdriver for this.
Fasten the 135mm fan onto the cooler unit using fan clips.
Connect the fan to the motherboard’s PWM signal.
When dismantling the 135mm fan, push the notches of the
fan clips away from the fan.
Introduction: Thank you for deciding to purchase a be quiet!
product. The following instructions will guide you through the
installation process. If you do encounter installation problems,
please don't hesitate to contact our customer services by
mailing service@bequiet.com. Please note that be quiet!
cannot accept liability for damage caused by compatibility
problems.
Warranty:
• 3 years manufacturer guarantee for consumers (original
purchase from authorized be quiet! dealers only)
• Guarantee work can only be processed with an included
copy of the purchase receipt from an authorized be quiet!
dealer
• Manipulation and structural changes of any kind as well
as damages through external mechanical forces lead to a
complete voiding of the guarantee
• Our General Warranty Conditions apply, which can be
viewed on bequiet.com
Listan GmbH
.
Wilhelm-Bergner-Straße 11c
.
21509 Glinde
Germany
For further information contact us via e-mail:
service@bequiet.com
SCOPE OF DELIVERY
General
We recommend preparatory mounting of the cooler outside
the PC case for subsequent installation.
The following parts are needed for this:
1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 2x Intel
mounting brackets (4), 1x cooler mounting bridge (7), 4x Intel
spacer nut A (8), 4x mounting bracket fastening screws (11), 2x
Mounting bridge fastening screws (12), 1x cross-tip screwdriver
(16) 1x thermal paste (17), 2x fan clips (18)
Assembly of the cooler mounting frame
First screw the Intel spacer nut A onto the threads of the
socket frame. Place the Intel mounting brackets over the Intel
spacer nuts and screw these tight with the mounting bracket
fastening screws. You can use the cross-tip screwdriver for
this.
Mounting the CPU cooler
First remove the protective foil from the underside of the
cooler. Spread the thermal paste on the surface of the CPU.
The amount supplied is sufficient for one or two applications.
Caution: The thermal paste supplied is not suitable for
human consumption. If swallowed, drink lots of water and
urgently seek medical attention. Keep it out of the reach of
children. Avoid contact with skin and eyes.
2011(-3) square ILM, 2066
General
We recommend preparatory mounting of the cooler outside
the PC case for subsequent installation.
The following parts are needed for this:
1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 1x Intel
backplate (3), 2x Intel mounting brackets (4), 1x cooler mounting
bridge (7), 4x Intel spacer nut B (9), 4x mounting bracket fastening
screws (11), 2x mounting bridge fastening screws (12), 4x Intel
backplate screws (13), 4x O-rings (15), 1x cross-tip screwdriver
(16), 1x thermal paste (17), 2x fan clips (18)
Mounting the backplate
Position the Intel backplate screws in the notches situated on
the rear side of the Intel backplate. Pay attention in so doing
to align with the holes drilled for each socket.
For fixing the backplate screws onto the Intel backplate use
the O-rings. Once assembly of the Intel backplate for the
respective Intel socket is complete, position it under the
motherboard. Make sure that the backplate screws are
precisely positioned inside the motherboard holes.
Installation of the mounting brackets
Screw the Intel spacer nut B onto the previously positioned
Intel backplate. Then position the Intel mounting brackets
over the Intel spacer nut B and affix these with the mounting
bracket fastening screws. You can use the cross-tip
screwdriver for this.
1200, 1150, 1151, 1155
Intel: LGA 2011 (-3) square ILM / LGA 2066
Intel: LGA 1200 / 1150 / 1151 / 1155
Part name Quantity
be quiet! Dark Rock 4 cooler 1
135mm fan 1
Intel backplate 1
Intel mounting brackets 2
Long AMD mounting brackets 2
Intel mounting brackets LGA
1700
2
Cooler mounting bridge 1
Intel spacer nut A 4
Part name Quantity
Intel spacer nut B 4
AMD spacer nuts 4
Mounting bracket fastening
screws
4
Mounting bridge fastening
screws
2
Intel backplate screws 4
AMD backplate screws 4
O-rings 4
Cross-tip screwdriver 1
Thermal paste 1
Fan clips 4
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
V1/22
www.bequiet.com/bk021
» Product information for this CPU cooler
» Produktinformationen zu diesem CPU-Kühler
» Informations produit pour ce système de refroidissement
» Información del producto para este refrigerador de CPU
» Informacje produktowe dla tego coolera CPU
» Engelstalige productinformatie voor deze processorkoeler
» Produktinformation för den här processorkylaren, på
engelska
» Подробнаяинформацияоданномкулередля
процессора
» 此CPU散熱器的產品資訊
» 此CPU散热器的产品信息
» 製品情報（クーラー）
NL
SE
18
Mounting the CPU cooler
First remove the protective foil from the underside of the
cooler. Spread the thermal paste on the surface of the CPU.
The amount supplied is sufficient for one or two applications.
Caution: The thermal paste supplied is not suitable for human
consumption. If swallowed, drink lots of water and urgently
seek medical attention. Keep it out of the reach of children.
Avoid contact with skin and eyes.
Position the cooler mounting bridge centrally on the cooler.
Next place the cooler unit onto the CPU. Insert the Intel/
mounting bridge fastening screws from above into the cooler
mounting bridge and then screw these alternately tight. You
can use the cross-tip screwdriver for this.
Mount the 135mm fan onto the cooler unit using the fan
clips. Connect the fan to the motherboard’s PWM signal.
When dismantling the 135mm fan push the notches of the fan
clips away from the fan.
Position the cooler mounting bridge centrally on the cooler.
Next place the cooler unit onto the CPU. Insert the mounting
bridge fastening screws from above into the cooler mounting
bridge and then screw these alternately tight. You can use the
cross-tip screwdriver for this.
Fasten the 135mm fan onto the cooler unit using fan clips.
Connect the fan to the motherboard’s PWM signal.
When dismantling the 135mm fan, push the notches of the
fan clips away from the fan.
Introduction: Thank you for deciding to purchase a be quiet!
product. The following instructions will guide you through the
installation process. If you do encounter installation problems,
please don't hesitate to contact our customer services by
mailing service@bequiet.com. Please note that be quiet!
cannot accept liability for damage caused by compatibility
problems.
Warranty:
• 3 years manufacturer guarantee for consumers (original
purchase from authorized be quiet! dealers only)
• Guarantee work can only be processed with an included
copy of the purchase receipt from an authorized be quiet!
dealer
• Manipulation and structural changes of any kind as well
as damages through external mechanical forces lead to a
complete voiding of the guarantee
• Our General Warranty Conditions apply, which can be
viewed on bequiet.com
Listan GmbH
.
Wilhelm-Bergner-Straße 11c
.
21509 Glinde
Germany
For further information contact us via e-mail:
service@bequiet.com
SCOPE OF DELIVERY
General
We recommend preparatory mounting of the cooler outside
the PC case for subsequent installation.
The following parts are needed for this:
1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 2x Intel
mounting brackets (4), 1x cooler mounting bridge (7), 4x Intel
spacer nut A (8), 4x mounting bracket fastening screws (11), 2x
Mounting bridge fastening screws (12), 1x cross-tip screwdriver
(16) 1x thermal paste (17), 2x fan clips (18)
Assembly of the cooler mounting frame
First screw the Intel spacer nut A onto the threads of the
socket frame. Place the Intel mounting brackets over the Intel
spacer nuts and screw these tight with the mounting bracket
fastening screws. You can use the cross-tip screwdriver for
this.
Mounting the CPU cooler
First remove the protective foil from the underside of the
cooler. Spread the thermal paste on the surface of the CPU.
The amount supplied is sufficient for one or two applications.
Caution: The thermal paste supplied is not suitable for
human consumption. If swallowed, drink lots of water and
urgently seek medical attention. Keep it out of the reach of
children. Avoid contact with skin and eyes.
2011(-3) square ILM, 2066
General
We recommend preparatory mounting of the cooler outside
the PC case for subsequent installation.
The following parts are needed for this:
1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 1x Intel
backplate (3), 2x Intel mounting brackets (4), 1x cooler mounting
bridge (7), 4x Intel spacer nut B (9), 4x mounting bracket fastening
screws (11), 2x mounting bridge fastening screws (12), 4x Intel
backplate screws (13), 4x O-rings (15), 1x cross-tip screwdriver
(16), 1x thermal paste (17), 2x fan clips (18)
Mounting the backplate
Position the Intel backplate screws in the notches situated on
the rear side of the Intel backplate. Pay attention in so doing
to align with the holes drilled for each socket.
For fixing the backplate screws onto the Intel backplate use
the O-rings. Once assembly of the Intel backplate for the
respective Intel socket is complete, position it under the
motherboard. Make sure that the backplate screws are
precisely positioned inside the motherboard holes.
Installation of the mounting brackets
Screw the Intel spacer nut B onto the previously positioned
Intel backplate. Then position the Intel mounting brackets
over the Intel spacer nut B and affix these with the mounting
bracket fastening screws. You can use the cross-tip
screwdriver for this.
1200, 1150, 1151, 1155
Intel: LGA 2011 (-3) square ILM / LGA 2066
Intel: LGA 1200 / 1150 / 1151 / 1155
Part name Quantity
be quiet! Dark Rock 4 cooler 1
135mm fan 1
Intel backplate 1
Intel mounting brackets 2
Long AMD mounting brackets 2
Intel mounting brackets LGA
1700
2
Cooler mounting bridge 1
Intel spacer nut A 4
Part name Quantity
Intel spacer nut B 4
AMD spacer nuts 4
Mounting bracket fastening
screws
4
Mounting bridge fastening
screws
2
Intel backplate screws 4
AMD backplate screws 4
O-rings 4
Cross-tip screwdriver 1
Thermal paste 1
Fan clips 4
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
V1/22
www.bequiet.com/bk021
» Product information for this CPU cooler
» Produktinformationen zu diesem CPU-Kühler
» Informations produit pour ce système de refroidissement
» Información del producto para este refrigerador de CPU
» Informacje produktowe dla tego coolera CPU
» Engelstalige productinformatie voor deze processorkoeler
» Produktinformation för den här processorkylaren, på
engelska
» Подробнаяинформацияоданномкулередля
процессора
» 此CPU散熱器的產品資訊
» 此CPU散热器的产品信息
» 製品情報（クーラー）
NL
SE
18
To Next Page
Need help?
General
Weight and Dimensions
