Beckett FR600 - User Manual

084-121076
This Beckett FR Series centrifugal pump is magnetically driven and contains no seals to leak or wear
out. It also contains no oil as other types of submersible utility pumps do, thereby eliminating the pos-
sibility of oil leaks which can foul your water. All electrical parts and connections are completely en-
capsulated with epoxy. These features, combined with very low energy consumption, make for a safe
and convenient pump which is economical to operate. In addition, it is essentially maintenance-free.
The Beckett FR Series pump is designed to operate completely submerged. Cleaning of the filter can
be reduced by placing the pump on a brick or patio stone in the water to raise it above the level of the
debris which accumulates on the bottom.
Use:
A prefilter is supplied with the pump. Using and maintaining a clean prefilter will greatly decrease
maintenance in cleaning the impeller assembly as well as providing better water filtration and pump
flow. See Page 2 - Prefilter Cleaning.
Prefilter:
The only serviceable part is the impeller assembly. It can be cleaned and inspected by removing the
four screws holding the volute housing in place and lifting out the housing and impeller assembly.
See Page 3 for diagram. Never attempt to disassemble the impeller assembly. If it becomes worn or
broken, simply replace the entire assembly. If the pump is taken out of service for a period of time
(such as during winter), flush the pump out with clean fresh water and drain thoroughly before stor-
ing. Ensure that the cord is protected from wear and abrasion.
NEVER ATTEMPT TO REPLACE OR SHORTEN THE CORD!
Service and
Maintenance:
1. RISK OF ELECTRIC SHOCK – This pump is supplied with a grounding conductor and a ground-
ing-type attachment plug (3-prong plug). To reduce the risk of electric shock, be certain that it is
connected only to a properly grounded, grounding-type receptacle. Do not remove the grounding
pin.
2. RISK OF SEVERE ELECTRIC SHOCK – Connect only to a grounded receptacle protected
by a ground-fault circuit-interrupter (GFCI). A GFCI must be provided in accordance with Section
680-51 of the national electric code. Contact a qualified electrician if you cannot verify that the
receptacle is protected by the GFCI.
3. TO REDUCE THE RISK OF ELECTRICAL SHOCK:
A. Never use an extension cord to connect unit to electrical supply; provide a properly located
GFCI outlet.
B. Never bury the 3-prong plug of the cord, it is not waterproof and severe electric shock will
occur.
Your Beckett FR Series pump is cooled and lubricated with water. If the pump is plugged in while it
is out of the water, it is normal for it to rattle. However, while it will continue to operate if allowed to
run dry, it will sustain permanent heat damage after 30 minutes. Your Beckett FR Series pump is in-
tended to pump fresh water only. Do not use to pump oils, solvents, fuels, or salt water. Do not allow
to freeze.
SAFETY
WARNING:
Note:
PUMP MODEL #
VOLTS Hz AMPS WATTS
MAX.
HEAD
APPROXIMATE PUMP FLOW (GPH @ HEAD)
USING 1” ID HOSE
0’ 1’ 3’ 5’
FR250 115 60 .45 31 5’-11” 350 290 200 80
FR400 115 60 .68 32 6’-6” 500 418 268 115
FR600 115 60 .75 34 7’-8” 680 600 437 283
FR800 115 60 .90 70 12’-9” 900 814 652 512
PUMP MODEL NUMBER AND INFO LOCATED ON PUMP BACKPLATE NEAR POWER CORD
CAUTION:
1. This pump has been evaluated for use with water only.
2. Disconnect pump from power source before handling, servicing or working in the water in which the
pump is operating.
B E C K E T T
C O R P O R A T I O N
N o r f o l k • V i r g i n i a

Summary

Safety Warnings

Risk of Electric Shock

Pump has grounding conductor; ensure proper connection to grounded receptacle.

Risk of Severe Electric Shock

Connect only to GFCI protected grounded receptacle; verify GFCI protection.

Reducing Electrical Shock Risk

Do not use extension cords; do not bury plug.

Assembly and Operation Instructions

Nozzle Adaptor Instructions

Details on installing spray head, waterbell, and bubbler nozzles.

Two-Way Valve Operation

Instructions for operating the two-way flow control valve.

Pump Installation

Guidance on placing the pump in the pond and connecting power.

Prefilter Cleaning

Steps to clean the pump filter when flow is reduced.

Customer Support and Parts

Contact Information

Phone number for customer service for troubleshooting and parts.

Pond Accessories

Bio-Filters

Provide mechanical and biological pond filtration for a cleaner and healthier environment.

Pre-Bio-Filter

Attaches to pump intake for enhanced filtration and camouflage.

UV Clarifier

Uses UV light to clarify green water and improve pond health.

Water Features

Spitters

Attach to pump for a secondary water feature returning water as a tube.

Water Course;Stream

Molded plastic features with rock texture for natural look, varying lengths.

Fountain Art

Figurines providing accent water features; larger than spitters.

Pond Accent Accessories

Pond Lights

Low voltage lights to add interest, dimension, and depth to pond areas.

Plant Baskets

Molded plastic baskets for pond plants to contain roots while allowing water flow.

Changing the Two-Way Valve to a One-Way Valve

Valve Option

Procedure to convert the two-way valve to a one-way valve.

Valve Conversion Process

Detailed steps for removing and reinserting valve components.

Customer Statement of Limited Warranty

Warranty Coverage

Details pump and rotor/impeller assembly warranty periods.

Warranty Claims

Instructions for making claims and required proof of purchase.

Warranty Exclusions

Conditions that void the warranty, such as damage or misuse.

Beckett FR600 Specifications

General

Brand	Beckett
Model	FR600
Category	Water Pump
Language	English