Need help?Do you have a question about the Behringer ULTRAGRAPH PRO FBQ1502 and is the answer not in the manual?
General| Type | Stereo Graphic Equalizer |
|---|---|
| Frequency Range | 25 Hz to 16 kHz |
| Inputs | 2 x XLR, 2 x 1/4" TRS |
| Outputs | 2 x XLR, 2 x 1/4" TRS |
| Maximum Input Level | +21 dBu |
| Maximum Output Level | +21 dBu |
| Noise (IHF-A) | -94 dBu |
| Power Supply | 100-240 V~, 50/60 Hz |
| Power Consumption | 15 W |
| Feedback Detection | Yes |
| Low Cut Filter | Yes |
| Signal-to-Noise Ratio | >95dB |
| Input Impedance | 10 kOhms balanced/unbalanced |
| Dimensions | 1.75 x 19 x 8.5 inches |
| Weight | 2.1 kg / 4.6 lbs |
General safety precautions and warnings for operating the audio equipment safely.
Information regarding technical specifications, appearance, and limitations of liability.
Details of the limited warranty, including coverage, exclusions, and how to claim service.
Instructions for registering the product online for efficient warranty processing.
Procedure for obtaining warranty service and return authorization.
Exclusions from the limited warranty, such as consumable parts and misuse.
Information that the limited warranty is only valid for the original buyer.
Limitations on MUSIC Group's liability for consequential or indirect damages.
Statement superseding other communications regarding product warranty.
Details on statutory consumer rights and how they interact with the limited warranty.
Notification that warranty conditions are subject to change without notice.
Explanation of the FBQ system for identifying and eliminating feedback frequencies using fader LEDs.
Description of the dedicated subwoofer output with adjustable cut-off frequency.
Information on adjusting the fader range from ±6 dB to ±12 dB.
Statement on the high quality standards and ISO9000 certification.
Explanation of the fail-safe relay bypass for power loss and switch-on thumps.
Details on electronically servo-balanced inputs/outputs and automatic signal level correction.
Instructions for inspecting the unit upon arrival and reporting any damage.
Guidance on ventilation, voltage selection, fuse replacement, and grounding.
Reminder to fill out and send the warranty card or register online.
Explanation of the manual's structure for mastering unit functions and controls.
Detailed description of front panel controls including level meters, FBQ switch, and faders.
Description of rear panel connectors (XLR, TRS) and identification labels.
Using the LIMITER switch to activate the limiter and understanding the limiter display.
Adjusting the THRESHOLD control to set the signal level for limiter activation.
Description of the balanced XLR and 1/4" TRS input connectors.
Description of the balanced XLR and 1/4" TRS output connectors.
Details of the balanced XLR SUB OUT connector for subwoofer signals.
Using the X-OVER FREQ control to set the subwoofer crossover frequency.
Activating the PINK NOISE switch and adjusting volume with NOISE LEVEL control.
Reading the signal level of the noise generator on the LED display.
Using pink noise for P.A. system adjustment and measuring frequency response.
Indication of the signal level at the SUB OUT connector via the LED display.
Adjusting the signal level of the subwoofer output using the LEVEL control.
Activating the subwoofer output by pressing the SUBWOOFER switch.
Diagram showing a typical setup of the ULTRAGRAPH PRO FBQ6200 as a master equalizer.
Advice on initial setup, distortion, loudspeaker placement, and phase correction.
General guidelines for EQ use, including intelligibility and respecting system limitations.
Recommendation to lower monitor volume during intermissions to create headroom.
Using the low-cut filter to remove deep frequencies for a clearer monitor sound.
Procedure for detecting and suppressing feedback frequencies in monitor systems using the FBQ switch.
Using the equalizer to graphic equalize studio monitors and suppress room resonance.
Using the equalizer for processing single-channel or master signals for a homogenous sound.
Using the equalizer to modify voices (e.g., telephone voice) or filter instruments.
Instructions for rack mounting the FBQ1502, FBQ3102, and FBQ6200 units.
Guidance on making audio connections using XLR and 1/4" TRS cables.
Diagram illustrating the wiring of an unbalanced 1/4" TS connector.
Diagram illustrating the wiring of a balanced 1/4" TRS connector.
Diagram for 1/4" TRS connector use in insert send/return applications.
Technical details for the FBQ1502 model, including audio inputs, outputs, and system specs.
Technical details for the FBQ3102 model, including audio inputs, outputs, and system specs.
Technical details for the FBQ6200 model, including audio inputs, outputs, and system specs.
To Next Page
