Why is my Beko Washer directly discharging the water it takes in?
If your Beko Washer is immediately discharging the water it takes in, the draining hose might not be at the correct height. Connect the water draining hose as described in the operation manual.
Why is my Beko WUX71031G-IT Washer washing performance poor with stains persisting?
If your Beko Washer's washing performance is poor and stains persist, it could be due to several reasons. Ensure you're using enough detergent, and avoid overloading the machine. Select the correct program and temperature for the laundry, and use the right type of detergent. Also, avoid using too much detergent and make sure to put the detergent in the correct compartment, without mixing bleaching agents and detergent.
Why is my Beko WUX71031G-IT Washer washing performance poor and laundry turning gray?
Poor washing performance with laundry turning gray in your Beko Washer can be due to insufficient detergent over time, washing at low temperatures for too long, or using too little detergent with hard water. Always use the recommended amount of detergent appropriate for water hardness and the laundry, and select the proper temperature for the laundry being washed. Avoid using too much detergent.
Why did my Beko WUX71031G-IT Washer stop shortly after the programme started?
Your Beko Washer might have stopped temporarily due to low voltage. It will resume running when the voltage restores to the normal level.
Why is there too much foam forming in my Beko Washer?
Excessive foam in your Beko Washer can be caused by using improper detergents for the machine, so use detergents appropriate for washing machines. Using too much detergent or storing it improperly can also lead to this issue. Some meshed laundry items may foam excessively, so use less detergent for them. Ensure the detergent is in the correct compartment, as well. In some cases, softener may be taken early due to valve or dispenser problems.
What to do if my Beko WUX71031G-IT programme cannot be started or selected?
If your Beko Washer programme cannot be started or selected, the washing machine may have switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). Press and hold the On / Off button for 3 seconds.
Why is my Beko WUX71031G-IT Washer programme time not counting down? (On models with display)
If the program time isn't counting down on your Beko Washer, the timer may stop during water intake until the machine takes in enough water. It might also stop during the heating step until the selected temperature is reached, or during the spinning step if the automatic unbalanced load detection system is activated due to unbalanced laundry distribution.
Why does my Beko WUX71031G-IT take longer than usual to wash?
The washing cycle on your Beko Washer might be taking longer due to several reasons. The water pressure could be low, so the machine waits until it takes in enough water. Low voltage or a low input water temperature can also extend the washing time. Additionally, the number of rinses or the amount of rinse water might have increased, or excessive foam might have occurred due to too much detergent usage, triggering the automatic foam absorption system; use the recommended amount of detergent.
Why is my Beko Washer vibrating so much and making noise?
Your Beko Washer might be vibrating or making noise due to several reasons. Ensure the machine is standing balanced by adjusting the feet. A hard substance might have entered the pump filter, so clean it. Remove the transportation safety bolts if you haven't already. The laundry quantity might be too little, so add more, or the machine might be overloaded, so take some out. Also, ensure the machine isn't leaning on anything.
What to do if my Beko Washer won't drain water?
If your Beko Washer isn't draining water, the water drain hose might be clogged or twisted, so clean or flatten it. Alternatively, the pump filter could be clogged, so clean the pump filter.
General| Type | Front Load |
|---|---|
| Capacity | 7 kg |
| Spin Speed | 1000 rpm |
| Weight | 62 kg |
| Noise Level (Spin) | 76 dB |
| Programs | 15 |
| Delay Start | Yes |
| Child Lock | Yes |
| Drum Material | Stainless Steel |
| Energy Efficiency Class | A+++ (-10%) |
To Next Page