Why my Belifu Massager does not turn on?
If your Belifu Massager unit doesn't turn on or the screen is dim, it's likely due to a low battery. The suggested solution is to recharge the battery.
Why Belifu Massager adhesive gel pads do not stick to skin?
If the adhesive gel pads of your Belifu Massager don't stick to your skin even after cleaning and moistening, it means the adhesive gel pads need to be replaced. You can replace the pads, which can be purchased from Belifu official store or by contacting support@belifu.com.
What to do if Belifu Massager is on, but no sensation is felt?
If your Belifu Massager is on, but you feel no sensation in the pads, it could be due to several reasons: * Both pads are not firmly on the skin. * There is a loose connection. * The intensity level needs to be increased. To fix this, make sure all pads are firmly pressed to the skin, ensure all connections are secure from the unit to the wires and from the wires to the pads, and increase the intensity level.
How to improve pain relief with Belifu FDES115 Massager?
If your Belifu Massager does not provide adequate pain relief, the cause may be not using it long enough. To address this, use your massager for 20-30 minutes at a time, 3-6 times per day.
Why Belifu FDES115 Massager causes burning sensation on skin?
If you experience a painful burning sensation or weakened stimulation with your Belifu Massager, it's likely because the adhesive gel pads aren't adhering firmly to the skin or are too dry. To resolve this, apply a few drops of water to the adhesive surface of each pad and ensure the pads are pressed firmly to the skin during application.
What to do if Belifu FDES115 makes me feel unwell?
If you're feeling unwell while using the Belifu Massager, it could be due to several factors: * The intensity is too strong. * Electrodes are too close together. * Electrodes or conductors are damaged. * The electrode area is too small. To address this, decrease the intensity, reorient the electrode position, replace the electrode wire or pads, or replace the electrode pad with a size larger than 4cm×4cm in area.
Why Belifu FDES115 Massager modes and channels flash?
If your Belifu Massager turns on but all the modes and channels flash, preventing you from selecting a mode or adjusting the intensity, it's because you must always use two pads (one channel) or four pads (two channels) at the same time. Ensure you have placed all pads on your body when using two pads (one channel) or four pads (two channels), otherwise it won't work.
How to pause Belifu Massager treatment?
To pause the treatment on your Belifu Massager, be aware that the machine must be in the locked state. During treatment, the machine will automatically enter the locked state after 30 seconds of inactivity, then you can press the [ ] to suspend the treatment.
Explains device operation and provides customer support contacts and download link.
Lists all items included with the HEAT TENS & EMS & MASSAGE UNIT.
Details the purpose of TENS, MASSAGE, and EMS modes and lists users who should avoid the device.
Describes the physical components and screen interface of the therapeutic apparatus.
Lists critical safety advice, contraindications, and important notes for device usage.
Step-by-step guide for initial setup and operation before starting a treatment.
Provides guidance on proper handling, application, and care of electrode pads to ensure optimal performance.
Explains the principles and benefits of TENS, MASSAGE, and EMS modes for pain relief and muscle stimulation.
Guides users on selecting appropriate treatment modes (TENS, MASS, EMS) and programs from 12 options.
Explains how to select the appropriate intensity level from 0 to 40 for personalized treatment.
Details how to select modes, programs, and adjust the heat function to three temperature levels.
Instructions on how to select treatment programs for the AB channel on the device.
Instructions on how to select treatment programs for the CD channel on the device.
Explains how to cycle through heat levels (E1, E2, E3, Off) using the heat button.
Guides users on setting the treatment time, with options to increase it incrementally up to 60 minutes.
Details how to increase or decrease stimulation intensity for AB and CD channels, with a maximum level of 40.
Explains how to pause and resume treatment, including the device's auto-lock feature for inactivity.
Covers adjusting treatment time during a session and the proper procedure for shutting down the device.
Explains battery indicators and provides instructions for cleaning electrode pads and the main unit.
Provides instructions for environmentally sound disposal and explains standardized symbols used in the manual.
Details the warranty period, conditions for claims, exclusions, and liability limitations for the device.
To Next Page
General
