Beninca PONY - Self-Regulation of the Functioning Parameters (AUTO)

2
1
EN
Self-regulation of the functioning parameters (AUTO)
The
fi
rst and most important
f
unction to pro
g
ram is the sel
f
-re
g
ulation o
f
the parameters, which allows the control unit to automatically set the end run points, the torque applied
t
o the lea
f
and the torque in the slowin
g
phase*.
D
uring the autoset operations, the control unit automatically per
f
orms several opening and closure manoeuvres.
B
e
f
ore proceedin
g
, check that no person, animal or obstacle is or can be in the door manoeuvre area.
A
ll the accessories provided for the s
y
stem should be alread
y
connected to the control unit. If further accessories should be added
,
s
elf-ad
j
ustment must be re
p
eated.
P
r
oceed
as
f
o
ll
o
w
s
:
1- Apply mains power supply to the automation via the pre-wired socket, usin
g
an extension if necessary.
2- Release the leave, take it manually to about hal
f
o
f
the run and block it again.
3- Start the autoset
p
hase as described below. As soon as the first manoeuvre starts, carefull
y
check that the leaf moves in the closure direction. If this is not the case,
p
ress
"

"
and
“
P
G
M” at the same time to interrupt the autoset. The display shows the ERR messa
g
e. Use the movement direction reverse button
(
MINV menu
)
and chan
g
e the direction of movement.
1
Press the button [P
G
M] to access programming.
PGM
2
T
he display shows AUTO, select Auto by pressin
g
the
[
PGM
]
button.
AUTO
3
A
UT
O
starts to flash slowly. Press and hold the
[
P
G
M
]
key, after 5 seconds AUT
O
starts to flash quickly, release the key only when the
display shows the PR
G
message.
4
T
he self-re
g
ulation phase starts, the display shows PRG. The control unit commands different openin
g
and closin
g
manoeuvres at
various s
p
eeds.
A
t the end of the manoeuvre the display shows “
O
K”
P
R
G
5
T
he control unit goes back to the AUT
O
menu. To exit programming, press the [P
G
M] and
[

]
b
uttons at t
h
e same t
i
me or, a
l
ternat
i
ve
l
y,
remove the
p
ower su
pp
l
y
or wait 60 seconds.
P
G
M
+

* The slowing phase must be activated via the T
S
M parameter. The control unit is supplied with the parameter set at 0 (
O
ff); the AUT
O
function does not activate slowing but i
s
l
imited to de
fi
ning a suitable torque value.
The intervention o
f
the photocells or any other command
f
rom the transmitter or key selector, interrupts the autoset phase, displayin
g
the messa
g
e ERR1
/
2
/
3. The
p
rocedure must therefore be re
p
eated.
Every self-re
g
ulation procedure overwrites the previous one.
P
erform an autosto
p
p
rocedure after ever
y
maintenance intervention or modification of the door.
Regulation of the automatic closure time (TCA)
The automatic closure function allows to set a time which, on ex
p
ir
y
, if the leaf is in the o
p
en
p
osition the control unit autonomousl
y
commands a closure manoeuvre.
With this
f
unction active, i
f
you
f
or
g
et to
g
ive the closure command or in the case o
f
simultaneous commands, the control unit closes the lea
f
a
f
ter the set time.
The
f
actory setting envisions 30 seconds be
f
ore automatic closure.
1
Press the [P
G
M] button to access programming or if the control unit is already in the programming menu, press [

] until the T
C
A
f
unction is displayed.
TCA
2
Press the
[
P
G
M
]
button to enter the T
C
A parameter re
g
ulation.
T
he display shows the current value of the T
C
A parameter.
Use the
[

]
key to select one of these values:
0
T
he T
C
A function is deactivated
.
1
T
he pause time is set at 10 seconds (de
f
ault setting
2
T
he
p
ause time is set at 30 seconds
)
3
Th
e
p
ause t
i
me
i
s set at 60 secon
d
s
4
Th
e pause t
i
me
i
s set at 90 secon
d
s
0000
0004
3
C
onfirm the desired value usin
g
the
[
P
G
M
]
key, the display shows PR
G.
PR
G
4
T
he control unit goes back to the T
C
A menu. To exit programming, press the [P
G
M] and [

]
b
uttons at t
h
e same t
i
me or, a
l
ternat
i
ve
l
y,
remove t
h
e power supp
l
y or wa
i
t 60 secon
d
s.
P
GM
+

Regulation of the motor thrust (PMOT)
The
f
orce applied is normally set automatically by the control unit durin
g
the sel
f
-re
g
ulation phase
(
AUTO
)
.
This menu can be used to modif
y
that set b
y
the control unit, to make u
p
for a friction
p
oint for exam
p
le
.
1
Press the
[
PGM
]
button to access pro
g
rammin
g
or if the control unit is already in the pro
g
rammin
g
menu, press
[

]
until the PMOT
function is dis
p
la
y
ed.
PMOT
p
m
ot
PMOTPMOT
2
Press the [P
G
M] button to enter the PM
O
T regulation.
T
he dis
p
la
y
shows the current value of the PMOT
p
arameter.
U
se t
h
e
[

]
key to select one o
f
these values:
1
l
ow motors torqu
e
2
medium/low motors tor
q
ue
3
medium
/
hi
g
h motors torque
4
hi
g
h motors torque
(
default settin
g
)
0001
0004
3
C
onfirm the desired value usin
g
the
[
P
G
M
]
key, the display shows PR
G.
P
R
G
4
T
he control unit
g
oes back to the PMOT menu. To exit pro
g
rammin
g
, press the
[
PGM
]
and
[

]
buttons at the same time or, alternatively,
remove t
h
e power supp
l
y or wa
i
t 60 secon
d
s.
P
GM+
