Beninca PONY - Selection of Photocell Functioning (PHCL); Selection of Direction of Rotation of the Motor (MINV); Resetting the Control Unit (Res)

23
EN
Selection of photocells functioning (PHCL)
It is possible to select the functioning mode of the photocells connected to the PHOT input. Normally, the photocells are active only in the closing phase, to allow the access of the
v
ehicle even when the
g
ate is not completely open. I
f
this intervention is also desired in the openin
g
phase, modi
f
y the parameter as
f
ollows:
1
P
ress the
[
P
G
M
]
button to access pro
g
rammin
g
or if the control unit is already in the pro
g
rammin
g
menu, press
[

]
until the PH
C
L
menu
i
s
di
s
pl
a
y
e
d
.
PMOT
P
HC
L
2
P
ress the
[
P
G
M
]
button to enter the PH
C
L re
g
ulation.
T
he display shows the current value of the PH
C
L parameter.
Use the
[

]
key to select one of these values:
ON
Ph
otoce
ll
s act
i
ve
i
n t
h
e open
i
n
g
an
d
c
l
os
i
n
g
p
h
ase
O
FF
P
hotocells only active in the closure phase
(
default
)
on
off
3
C
onfirm the desired value usin
g
the
[
P
G
M
]
key, the display shows PR
G.
P
R
G
4
T
he control unit
g
oes back to the PHCL menu. To exit pro
g
rammin
g
, press the
[
PGM
]
and
[

]
buttons at the same time or, alternatively,
remove t
h
e power supp
l
y or wa
i
t 60 secon
d
s.
PGM
+

Selection of direction of rotation of the motor (MINV)
The slidin
g
g
ates can open by slidin
g
to the ri
g
ht or to the le
f
t, as indicated in Fi
g
ure.
SX
OPEN
OPEN
DX
The direction of rotation may have to be inverted accordin
g
to the position of the motor
.
1
Press the
[
P
G
M
]
button to access pro
g
rammin
g
or if the control unit is already in the pro
g
rammin
g
menu, press
[

]
unt
il
t
h
e
MINV
menu
i
s
di
s
pl
a
y
e
d
.
PMOT
M
IN
V
2
Press the
[
PGM
]
button to enter the MINV re
g
ulation.
T
he dis
p
la
y
shows the current value o
f
the MINV
p
arameter.
U
se t
h
e
[

] key to select one o
f
these values:
C
__
O
M
otor with openin
g
to the ri
g
ht
O
__
C
M
otor with le
f
t openin
g
-
de
f
ault settin
g
-
o--c
c--o
3
Confirm the desired value usin
g
the
[
PGM
]
key, the display shows PRG
.
P
R
G
4
The control unit
g
oes back to the MINV menu. To exit pro
g
rammin
g
, press the
[
P
G
M
]
and
[

]
b
uttons at t
h
e same t
i
me or, a
l
ternat
i
ve
l
y,
remove the
p
ower su
pp
l
y
or wait 60 seconds.
P
G
M
+

Energy saving functioning mode (ESA)
W
ith the “E
S
A” energy saving function activated ,when a full opening or closing cycle is complete the control panel is in a condition of full energetic efficiency ,reducing at the
minimum the ener
g
etic consumption by takin
g
off power supply from the transformer and accessories.
1
Press the
[
P
G
M
]
button to access pro
g
rammin
g
or if the control unit is already in the pro
g
rammin
g
menu, press
[

]
until the E
S
A
f
unction is dis
p
la
y
ed.
PMOT
ES
A
2
P
ress the
[
PGM
]
button to enter the
ESA
regulation.
A
T
he dis
p
la
y
shows the current value o
f
the
ESA
parameter.
A
ON
ESA
mode activated (default)
A
OFF
ESA
mode deactivated
A
on
off
3
C
onfirm the desired value using the [P
G
M] key, the display shows PR
G
.
P
R
G
4
T
he control unit
g
oes back to the ESA menu. To exit pro
g
rammin
g
, press the
[
PGM
]
and
[

]
buttons at the same time or, alternatively,
remove the
p
ower su
pp
l
y
or wait 60 seconds.
P
G
M
+

Note :The E
S
A function does not work when the charger is in charging mode. The E
S
A function must be disabled when there is the need of keeping the accessories output always
activated ,
f
or example when a 24Vdc keypad or any other device that needs constant power supply is linked to the control panel.
Resetting the control unit (Res)
This function annuls all settin
g
s made, takin
g
the control unit back to the initial conditions. It also deletes the settin
g
s of the autostart procedure.
NOTE: An
y
remote controls memorised in the radio receiver are not deleted.
1
P
ress the [P
G
M] button to access programming or if the control unit is already in the programming menu, press [

] until the Res
f
unc
-
ti
on
i
s
di
sp
l
aye
d
.
PMOT
RES
2
P
ress and hold
[
PGM
]
, the RES messa
g
e starts to flash quickly.
3
Release the
[
PGM
]
button when the PRG messa
g
e is displayed.
T
he control unit is now taken to factor
y
values.
P
R
G
4
T
he control unit
g
oes back to the RE
S
menu. To exit pro
g
rammin
g
, press the
[
P
G
M
]
and
[

]
b
uttons at t
h
e same t
i
me or, a
l
ternat
i
ve
l
y,
remove the
p
ower su
pp
l
y
or wait 60 seconds.
P
G
M
+
