Beninca PONY - Complete Deletion of the Receiver Memory (RADI>RTR)

25
EN
Remote controls quick duplication
I
f
you have a transmitter that is already memorised (TX1), it can be duplicated (TX2) without accessing the control unit
f
or programming, proceed as
f
ollows:
1
G
ive an openin
g
command and wait till the leaf is in full openin
g
position usin
g
a transmitter already stored in memory
(
TX1
)
,
(
T
CA
f
unction must be enabled ).
PMOT
2
Press the hidden key o
f
the transmitter ,the code o
f
which has already been stored in memory (TX1)
TX
1
3
Wi
t
hi
n 5 secon
d
s ,press t
h
e a
l
rea
d
y memor
i
ze
d
transm
i
tter
k
ey correspon
di
ng to t
h
e c
h
anne
l
to
b
e matc
h
e
d
to t
h
e new transm
i
tter.
T
he flashin
g
li
g
ht switches on.
TX
1
4
W
ithin 10 seconds ,press the hidden key of the new transmitter
(
TX2
)
.
TX
2
5
W
ithin 5 seconds ,press the key o
f
the new transmitter to be matched to the channel to be matched at the item 2 ,the
f
lashin
g
li
g
ht
switches o
ff
.
TX2
6
T
he receiver stores the new transmitter code and exits
f
rom the programming mode immediately.
Complete deletion of the receiver memory (RADI>RTR)
T
o delete the memory completely, eliminatin
g
all previously-inserted remote controls, proceed as follows
:
1
Press the
[
PGM
]
button to access pro
g
rammin
g
or if the control unit is already in the pro
g
rammin
g
menu, press
[

]
until the Radi
menu is dis
p
la
y
ed.
PMOT
Ra
d
i
2
P
ress the
[
P
G
M
]
button to enter the Radi function.
T
he display shows the
fi
rst sub-menu PP.
Press
[

]
three times to display the RTR sub-menu
r
tr
3
P
ress the
[
PGM
]
button to enter the RTR function, the RTR messa
g
e starts to flash slowly.
Press
[
PGM
]
, the PRG messa
g
e is displayed and deletin
g
starts.
4
When the PR
G
message switches off, the display shows the
O
K message for about 2 seconds. All remote controls are now deleted
f
rom the memory
.
P
R
G
6
The control unit
g
oes back to the RADI>RTR menu. To
g
o back to the RADI menu, press the
[
PGM
]
and
[

]
buttons at the same time.
To exit pro
g
rammin
g
, press the
[
PGM
]
and
[

]
buttons at the same time a
g
ain or, alternatively, remove the power supply or wait 60
secon
d
s.
PG
M+

ARC com
p
atible control uni
t
IMPORTANT, PLEASE READ CAREFULLY
:
The radio receiver in this product is compatible with the new AR
C
(
Advanced Rollin
g
C
ode
)
transmitters which, thanks to 128-bit encryption ensure superior copy-security
.
Storing new ARC transmitters is quite similar to that of normal rolling code transmitters with HCS coding, but be aware that
:
1) AR
C
transmitters and Rolling
C
ode H
CS
can not be stored in a single receiver.
2
)
The first transmitter memorized determines the type of transmitters to be used later. If the first transmitter memorized is ARC, you can not store Rollin
g
code HCS transmitters,
an
d
v
i
ce versa.
3) Fixed code transmitters may only be used in conjunction with Rolling code H
CS
transmitters. They are, therefore, not usable in combination with the AR
C
transmitters
.
4
)
I
f
you want to chan
g
e the type o
f
transmitters it is necessary to proceed with a receiver reset
(
as described in the manual
)
.