16
PRE
Forewarning flashing light enabled or disabled.
Off: disabled forewarning flashing light.
On: enabled forewarning flashing light. The flashing light is activated 3 sec before the motor starts.
(OFF)
htr
The Service Man function is enabled or disabled.
Off: Automatic operation.
On: Service Man operation.
The OPEN/CLOSE push-buttons should be kept pressed for the entire operating time.
(OFF)
BLC
The lock function is enabled or disabled.
Off: Lock function disabled.
On: Lock function enabled. After the triggering of the closure limit switches, the control
unit delays the stop by approx. 0.5sec in order to allow a better resting of the gate leaf
onto the stoppers. DAS input is activated in the closing phase only.
Note: In case of sliding gates, leave to OFF.
(OFF)
Enc
Enables or disables the absolute Encoder input (ENC ASS connector).
On: Motor with absolute Encoder.
Off: Motor with no absolute Encoder.
(ON)
disg
Auxiliary capacitor
On: 230Vac motor - single-phase and Auxiliary capacitor (terminal 7/8)
Off: 400Vac motor - Three-phase .
(OFF)
Pho1
Photocell 1 input in the opening phase is enabled or disabled.
On: Photocell 1 is activated in the closing phase only.
Off: Photocell 1 is activated in both opening and closing phases.
(OFF)
Pho2
Photocell 2 input in the opening phase is enabled or disabled.
On: Photocell 2 is activated in the closing phase only.
Off: Photocell 2 is activated in both opening and closing phases.
(OFF)
Pho3
Photocell 3 input in the opening phase is enabled or disabled.
On: Photocell 3 is activated in the closing phase only.
Off: Photocell 3 is activated in both opening and closing phases.
(OFF)
Pho4
Photocell 4 input in the opening phase is enabled or disabled.
On: Photocell 4 is activated in the closing phase only.
Off: Photocell 4 is activated in both opening and closing phases.
(OFF)
tst1
Activates or deactivates the photocell test connected to the PHOT1 input
Prior to performing the operation, the unit checks the switching of the photocell contact.
If the check fails, the operation does not start.
On: photocell test activated.
Off: photocell test deactivated.
(OFF)
tst2
As with TST1 but refers to PHOT2 input
(OFF)
tst3
As with TST1 but refers to PHOT3 input (OFF)
tst4
As with TST1 but refers to PHOT4 input (OFF)
rem
(Enables or disables remote radiotransmitters learning, as indicated in the paragraph “Remote
transmitters learning”.
On: Remote learning enabled.
Off: Remote learning not enabled.
(ON)
RADIO (RADi)
MENU FUNZIONE
PP
By selecting this function, the receiver goes in waiting (Push) for a transmitter code to assign to the step-step function.
Press the key of the transmitter to assign to this function.
If the code is valid, it is memorised and the message OK is displayed
If the code is not valid, the message Err is displayed
2Ch
By selecting this function, the receiver goes into waiting (Push) for a transmitter code to assign to the second radio channel.
Press the key of the transmitter to assign to this function.
If the code is valid, it is memorised ad the OK message is displayed
If the code is not valid, the message Err is displayed.
ped
By selecting this function, the receiver goes into waiting (Push) for a transmitter code to assign to the pedestrian opening function
(see parameter TPED).
Press the key of the transmitter to assign to this function.
If the code is valid, it is memorised ad the OK message is displayed
If the code is not valid, the message Err is displayed.
ntx
By selecting this function the LCD screen shows the number of transmitters memorized into the receiver.
CLR
By selecting this function, the receiver goes into waiting (Push) for a transmitter code to erase from the memory.
If the code is valid, it is erased and the message OK is displayed
If the code is not valid or not present in memory, the message Err is displayed
RTR
Completely erases memory of the receiver. Confirmation of the operation is requested.
By selecting this function the receiver goes into waiting (Push) for a new PGM pressure to confirm the operation.
At end of erasing the OK message is displayed
To Next Page
Loading...
