To Next PageTo Next PageWhy is my Bestway Swimming Pool Vacuum not picking up debris?
If your Bestway Swimming Pool Vacuum isn't picking up debris, there might be several reasons. First, the battery could be low, so try charging it again. Also, the suction mouth could be clogged; clear any obstructions. Another possibility is that the debris compartment is full, so you should clean both the compartment and the filter cover.
How to make Bestway Flowclear Aquarover 58622 cover the entire pool?
If your Bestway Swimming Pool Vacuum isn't covering the entire pool, start by cleaning the debris compartment. If that doesn't solve it, the filter compartment might need cleaning, and the robot should be recharged for 6 hours. Also, water circulation from the filtration system can interfere with movement; turn off the filtration system for at least 15 minutes before operating the robot. Check the wheel for any obstructions and remove them. Ensure the locking pin is properly adjusted. Algae can also make the pool floor slippery, causing the robot to go in circles, so scrub the pool bottom and robot wheels.
What to do if Bestway Flowclear Aquarover 58622 moves slowly?
If your Bestway Swimming Pool Vacuum is moving slowly or not at all, the debris compartment might be full, or the filter cover could be clogged; clean the debris compartment and flush the screen with water, using a soft brush if necessary. Also, the suction mouth may be clogged; remove any obstructions. The impeller could also be jammed; power off the robot and inspect the hole under the swivel head for any large debris.
Why Bestway Flowclear Aquarover 58622 Swimming Pool Vacuum stopped moving in the middle of the pool?
If your Bestway Swimming Pool Vacuum stops moving in the middle of the pool but the swivel head is still turning, it may be stopped by an obstacle or large creases in the pool liner; check for and remove any obstructions. Alternatively, suction from the main drain of the pool floor could be the cause; turn off the filtration system.
How to fix Bestway Swimming Pool Vacuum that cannot be charged?
If your Bestway Swimming Pool Vacuum cannot be charged or recharged, ensure that the charging base is correctly and fully connected to both the external adapter and the robot, referring to the instruction manual for guidance.
How to troubleshoot Bestway Flowclear Aquarover 58622 Swimming Pool Vacuum swivel head that won't turn?
If the swivel head on your Bestway Swimming Pool Vacuum isn't turning or is turning noticeably slowly, check for debris hindering the movement of the side flap and remove it. Also, the swivel head bottom may be jammed; detach the swivel head and smoothening-ring, remove any trapped debris, verify the smoothening-ring and bottom plate are installed correctly, and inspect the smoothening-ring for damage, replacing it if necessary.
Why does debris escape from Bestway Swimming Pool Vacuum?
If debris is escaping from your Bestway Swimming Pool Vacuum, it may be because debris is clogged at the suction mouth, preventing the flap from closing; remove any clogged debris from the suction mouth.
How to stop Bestway Flowclear Aquarover 58622 Swimming Pool Vacuum from moving along the pool wall?
If your Bestway Swimming Pool Vacuum is moving along the pool wall, ensure that the locking pin is properly adjusted and that the robot's front/back faces the pool wall at the beginning of operation.
Why does Bestway Swimming Pool Vacuum operation last shorter than advertised?
If your Bestway Swimming Pool Vacuum operation lasts shorter than advertised, the battery may not be fully charged; charge the robot for at least 6 hours.
Why does Bestway Flowclear Aquarover 58622 swivel head rotates repeatedly?
The swivel head on your Bestway Swimming Pool Vacuum may rotate repeatedly for a few minutes once the robot sinks to the pool bottom because air is trapped inside the robot. This will stop once the air is discharged, and the robot will begin to move regularly.
General| Brand | Bestway |
|---|---|
| Model | Flowclear Aquarover 58622 |
| Category | Swimming Pool Vacuum |
| Language | English |
Ensures safe operation by detailing immersion, temperature limits, electrical safety, and preventing hazards like suction entrapment and toxic substance contact.
Defines responsibilities for child supervision, operation by individuals with reduced capabilities, and user maintenance.
Outlines mandatory steps for safely removing and disposing of the battery according to local regulations and environmental requirements.
Provides critical usage advice for pools, including avoiding pool shock, using only approved accessories, and handling saltwater environments.
Details safe practices for charging the robot, handling its cable, and preparing for storage to maintain performance.
Guides users through the essential steps for the initial charging process and setting up the robot for first-time use.
Explains how to adjust the robot's movement patterns and settings based on the pool's dimensions for optimal coverage.
Provides instructions for proper storage, including charging, cleaning, draining, and environmental conditions to preserve battery life.
Details the step-by-step process for safely removing the battery pack, requiring specific tools and careful disassembly.
Advises on the environmentally responsible disposal of the electrical product, emphasizing recycling and local authority guidance.
A comprehensive guide to diagnosing and resolving common operational problems, from debris capture failures to charging issues.
