Why are the pump adapters not level with the spa adapters on my Bestway Swimming Pool?
One characteristic of PVC is that it changes shape, which is normal. Elevate the pump with wood or another type of insulated material to bring the pump's adapters level with the spa's adapters.
Why is Lay-Z-Massage System not working on my Bestway LAY-Z-SPA Hot Tub?
If the Lay-Z-Massage System on your Bestway Hot Tub isn't working, it could be due to the air pump overheating. Try unplugging the pump and waiting two hours for it to cool down before plugging it back in and pressing the Lay-Z-Massage System Button. Also, the Lay-Z-Spa Massage stops automatically, so press the Lay-Z-Massage System Button to reactivate it.
What to do if my Bestway Hot Tub pump does not heat properly?
If your Bestway Hot Tub pump isn't heating properly, consider these possible solutions: * Ensure the temperature isn't set too low; adjust it to a higher setting. * Clean or replace the filter cartridge. * Unplug the pump and allow it to cool down completely before restarting if the thermal cut-out has activated. Make sure that the water temperature reaches 35°C (95°F) or lower. * Attach the cover to the spa.
How to clean the water in my Bestway Swimming Pool?
If the water in your Bestway Swimming Pool is not clean, it could be due to insufficient filtering time, so increase filtration time. Another reason may be a dirty filter cartridge, in which case you should clean or replace the filter cartridge. Improper water maintenance can also cause this issue; refer to the chemical manufacturer’s instructions for proper maintenance.
Why is the water in my Bestway Swimming Pool not clean?
The water in your Bestway Swimming Pool might not be clean due to insufficient filtering time. Try increasing the filtration time. Another cause might be a dirty filter cartridge; clean or replace it. Improper water maintenance could also be the reason; in this case, refer to the chemical manufacturer’s instructions.
What to do if my Bestway Swimming Pool pump does not operate?
If your Bestway Swimming Pool pump isn't operating, first check the power source to ensure there isn't a power failure. If the power source is fine, then the power circuits might be broken.
How to level pump adapters with spa adapters on Bestway Hot Tub?
If the pump adapters are not level with the spa adapters on your Bestway Hot Tub, elevate the pump with wood or another type of insulated material to bring the pump's adapters level with the spa's adapters.
What to do if water leaks from the adapters between the pump and spa of Bestway LAY-Z-SPA Hot Tub?
Insert the stopper caps on to the spa’s ports to prevent water from escaping and disconnect the pump. Check and make sure the seals are placed correctly inside the pump adapters. If the seals are correctly in place, reconnect the pump to the spa and hand-tighten the adapters.
How to level Bestway Swimming Pool pump adapters with spa adapters?
One characteristic of PVC is that it changes shape, which is normal. Elevate the pump with wood or another type of insulated material to bring the pump's adapters level with the spa's adapters.
How to troubleshoot the Lay-Z-Massage System on my Bestway Swimming Pool?
If the Lay-Z-Massage System on your Bestway Swimming Pool isn't working, the air pump may be overheating. Unplug the pump and wait two hours until it has cooled down, then plug it back in and press the Lay-Z-Massage System Button. If the Lay-Z-Spa Massage stops automatically, press the Lay-Z-Massage System Button to reactivate it. In case the air pump is broken, contact your local Bestway Aftersales Service Center for instructions.
General| Control Panel | Digital control panel |
|---|---|
| Power Saving Timer | Yes |
| Shape | Round |
| Capacity | 4-6 people |
| Max Heat Capability | 40℃ (104℉) |
| Certifications | CE |
| Included Accessories | repair patch |
To Next Page