BGS technic 3260-1 - User Manual

BGS technic KG
Bandwirkerstr. 3
D-42929 Wermelskirchen
Tel.: 02196 720480
Fax.: 02196 7204820
mail@bgs-technic.de
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
BGS 3260-1
Air Body Saw
TECHNICAL DATA
Strokes per min.: max. 9000
Sawing depth: 10 mm
Working Pressure: 90 PSI (6.3 Bar)
Air Inlet: 1/4" (6.3 mm)
Recommended air hose: 3/8" (10 mm)
Length with blade: 270 mm
Air Consuption: 1.8 CFM (51.6 l/min)
Air exhaust: Front
Noise Level: LpA = 88.15 dB (A)
LwA = 99.15 dB (A)
Vibration Level: ahd = 15.06 m/s²
K = 1.99 m/s²
Weight: 0.65 Kg
CA
UTION
Read and understand all rights and information in this manual.
Failure to comply with unconscious rights and information may include control and oversight.
Keep the operating instructions in a certain and controlled place for future reference.
S
AFETY INSTRUCTIONS
•
Ensure that the tool is in the OFF position when it is connected to the compressed air
system.
• Always wear approved safety glasses when using compressed air tools. Wear a suitable
r
espirator when dust is whirled up.
• Only use accessories suitable for compressed air. Risk of injury.
• Disconnect the tool from the compressed air supply before installing accessories or
performing maintenance or before the device is not in use.
• Always use the tool with common sense. Do not wear loose clothing or jewelry that can be
caught by moving parts as it can cause injury. Only operate the tool at a safe distance from
yourself and others.
• Observe the manufacturer's instructions for the compressed air system when installi
ng
r
egulators, filters and other accessories.
• Keep children and other unauthorized persons away from the work area.
• Do not let children play with the tool or its packaging.
AIR SOURCE
Clean and dry air and a correct air pressure is recommended as air supply for this air tool.
Maximum of 90 PSI at the air tool is recommended for most air tools of this class. Check specifications
section for recommended pressure. (Depending on length of air hose and other circumstances, air
pressure at compressor may need to be increased to 100 PSI to ensure 90 PSI at the tool. Water in the air
hose and compressor tank contributes to reduced performance and damage of the air tool. Drain the air
tank and filters before each use and as necessary to keep the air supply dry. Hose length over 25” causes
loss in line pressure. Increase hose ID or increase compressor pressure to compensate the pressure loss.
Use an in-line pressure regulator with gauge if air inlet pressure is critical.

Summary

Technical Data and Specifications

Operating Parameters

Details on strokes, depth, working pressure, air inlet, hose size, length, consumption, exhaust, noise, and vibration levels.

Weight and Safety Precautions

Information on the tool's weight and essential safety instructions for operation and maintenance.

Air Supply and Operation Guidance

Recommended Air Supply Components

Identifies essential components for a proper compressed air supply system for the tool.

Service and Maintenance Procedures

Guidelines for oiling, operating pressure, and general care of the compressed air device.

Application and Usage Instructions

Guidance on how to correctly use the Air Body Saw for cutting operations.

Blade Management and Sawing Techniques

Changing Saw Blades Safely

Step-by-step instructions for safely replacing the saw blade on the tool.

Sawing Operation

Instructions on adjusting speed and operating the trigger for sawing.

Maintenance, Troubleshooting, and Disposal

Lubrication and Maintenance Recommendations

Essential steps for lubricating the tool and maintaining the air supply system.

Troubleshooting Common Power Issues

Identifies probable causes for insufficient power and provides solutions.

Environmental Protection and Disposal

Guidelines for environmentally friendly disposal and recycling of the product.

Parts Identification

Exploded View and Parts List

Diagram of the tool's components and a detailed list of all parts with numbers.

CE Declaration of Conformity

EU Declaration of Conformity

Statement confirming the product's compliance with relevant EU directives and standards.

BGS technic 3260-1 Specifications

General

Brand	BGS technic
Model	3260-1
Category	Saw
Language	English