Bianchi e-Omnia - Declaration of Conformity; General Safety Warnings; Product Intended Use; Omnia C-Type and Omnia T-Type

4
EN
DECLARATION OF CONFORMITY
The manufacturer F.I.V.E. Bianchi S.p.A., located at Via delle Battaglie, 5 - 24047 Treviglio (BG), Italy, hereby declares that its products
conform with standards 2006/42/EC, 2014/30/UE, 2011/65/EU, 2014/53/EU, UNI EN15194:2018 and ISO4210. The products also conform with
the provisions of Art. 50 of the Italian Highway Code (Italian Legislative Decree no. 285 of 30 April 1992, as amended, and as amended by
Art. 24/1 of Italian Law no. 14 of 3 February 2003), as defined by Art. 2, paragraph 1, letter (n) of the Agreement.
The complete list of product codes and the relative compliance information can be consulted under the “Declaration of Conformity” link at
https://www.bianchi.com/manuals/.
GENERAL SAFETY WARNINGS
Please pay close attention to the following symbols.
DANGER!
indicates a potential danger which may cause serious injury or death if not avoided.
WARNING!
indicates practices and conduct to be adopted for safe product use.
INFORMATION!
indicates additional information on how to use the product.
WARNING!
Please note that failure to comply with the warnings and provisions contained in this data sheet exempts the manufacturer of any
liability.
INTENDED USE OF THE OMNIA CTYPE AND OMNIA TTYPE
ASTM CATEGORY 1
Racing, triathlon and time trial bikes, recreational bikes and city bikes including the e-Bike Pedelec versions.
Designed for use on paved surfaces such as asphalt roads and cycleways. The tires remain in constant contact with the ground.
INTENDED USE OF THE OMNIA XTYPE AND OMNIA FXTYPE
ASTM CATEGORY 3
Mountain bikes for cross-country and cycle touring with suspension fork including the e-Bike Pedelec versions.
Intended for use on category 2 surfaces as well as unpaved hiking trails with medium unevenness and drops up to 61 cm
(24 inches).
WARNING!
With the use of rear stands, mudguards, cargo racks and bicycle trailers, the intended use of the model changes to category 2 (see the
chapter on intended use in the user manual).
13 June 2023
C8005092-008
User manual supplement:
e-OMNIA
• Declaration of Conformity
The manufacturer F.I.V.E. Bianchi S.p.A., located at Via delle Battaglie, 5 - 24047 Treviglio (BG), Italy, hereby declares that its products
conform with standards 2006/42/EC, 2014/30/UE, 2011/65/EU, 2014/53/EU, UNI EN15194:2018 and ISO4210. The products also
conform with the provisions of Art. 50 of the Italian Highway Code (Italian Legislative Decree no. 285 of 30 April 1992, as amended,
and as amended by Art. 24/1 of Italian Law no. 14 of 3 February 2003), as defined by Art. 2, paragraph 1, letter (n) of the Agreement.
The complete list of product codes and the relative compliance information can be consulted under the “Declaration of Conformity”
link at https://www.bianchi.com/manuals/ .
• General safety warnings
Please pay close attention to the following symbols.
(symbol)Danger! indicates a potential danger which may cause serious injury or death if not avoided.
(symbol)Warning! indicates practices and conduct to be adopted for safe product use.
(
symbol)Information! indicates additional information on how to use the product.
(symbol)Warning!
Please note that failure to comply with the warnings and provisions contained in this data sheet exempts the manufacturer of any
liability.
• Intended use of the Omnia C-Type and Omnia T-Type
ASTM CATEGORY 1 - Racing, triathlon and time trial bikes, recreational bikes and city bikes including the e-Bike Pedelec versions.
Designed for use on paved surfaces such as asphalt roads and cycleways. The tires remain in constant contact with the ground.
• Intended use of the Omnia X-Type and Omnia FX-Type
ASTM CATEGORY 3 - Mountain bikes for cross-country and cycle touring with suspension fork including the e-Bike Pedelec versions.
Intended for use on category 2 surfaces as well as unpaved hiking trails with medium unevenness and drops up to 61 cm (24 inches).
(symbol)Warning!
With the use of rear stands, mudguards, cargo racks and bicycle trailers, the intended use of the model changes to category 2 (see
the chapter on intended use in the user manual).
• Frame
The frame is made entirely of aluminium, with tubing designed to add sportiness to e-Omnia products. Specifically designed to be
compatible with the motor and integrated battery, mounted in a balanced position to optimise riding agility.
Internal cable housing, casing and brake hoses.
The head tube is designed to house bearings from 1½”.
The frame is compatible with electronic and mechanical (chain and belt) shifting systems.
The frames conform to standard EN15194.
The maximum load capacity of the bike, system weight*, is indicated on the EPAC label, located in the motor housing unit.
13 June 2023
C8005092-008
User manual supplement:
e-OMNIA
• Declaration of Conformity
The manufacturer F.I.V.E. Bianchi S.p.A., located at Via delle Battaglie, 5 - 24047 Treviglio (BG), Italy, hereby declares that its products
conform with standards 2006/42/EC, 2014/30/UE, 2011/65/EU, 2014/53/EU, UNI EN15194:2018 and ISO4210. The products also
conform with the provisions of Art. 50 of the Italian Highway Code (Italian Legislative Decree no. 285 of 30 April 1992, as amended,
and as amended by Art. 24/1 of Italian Law no. 14 of 3 February 2003), as defined by Art. 2, paragraph 1, letter (n) of the Agreement.
The complete list of product codes and the relative compliance information can be consulted under the “Declaration of Conformity”
link at https://www.bianchi.com/manuals/ .
• General safety warnings
Please pay close attention to the following symbols.
(symbol)Danger! indicates a potential danger which may cause serious injury or death if not avoided.
(symbol)Warning! indicates practices and conduct to be adopted for safe product use.
(
symbol)Information! indicates additional information on how to use the product.
(symbol)Warning!
Please note that failure to comply with the warnings and provisions contained in this data sheet exempts the manufacturer of any
liability.
• Intended use of the Omnia C-Type and Omnia T-Type
ASTM CATEGORY 1 - Racing, triathlon and time trial bikes, recreational bikes and city bikes including the e-Bike Pedelec versions.
Designed for use on paved surfaces such as asphalt roads and cycleways. The tires remain in constant contact with the ground.
• Intended use of the Omnia X-Type and Omnia FX-Type
ASTM CATEGORY 3 - Mountain bikes for cross-country and cycle touring with suspension fork including the e-Bike Pedelec versions.
Intended for use on category 2 surfaces as well as unpaved hiking trails with medium unevenness and drops up to 61 cm (24 inches).
(symbol)Warning!
With the use of rear stands, mudguards, cargo racks and bicycle trailers, the intended use of the model changes to category 2 (see
the chapter on intended use in the user manual).
• Frame
The frame is made entirely of aluminium, with tubing designed to add sportiness to e-Omnia products. Specifically designed to be
compatible with the motor and integrated battery, mounted in a balanced position to optimise riding agility.
Internal cable housing, casing and brake hoses.
The head tube is designed to house bearings from 1½”.
The frame is compatible with electronic and mechanical (chain and belt) shifting systems.
The frames conform to standard EN15194.
The maximum load capacity of the bike, system weight*, is indicated on the EPAC label, located in the motor housing unit.