Biohit mLINE m10 - User Manual

Questions and Answers

A
alexadiazAug 16, 2025
Why is my Biohit mLINE m10 Laboratory Equipment pipette leaking or dispensing too small a volume?
- K
  Kelly SnyderAug 16, 2025
  Several factors can cause leakage or insufficient volume: * A newly attached tip might have non-uniform wetting of the plastic, so attach a new tip. * The tip might not be firmly attached; ensure it is properly secured. * The tip might be unsuitable; use original tips. * Foreign particles might be present between the tip and tip cone; clean the tip cone and attach a new tip. * The tip cone holder might not be tightened correctly; tighten it. * The pipette might be damaged; in this case, return it to your Biohit service representative for servicing.
M
Mrs. Rebecca McguireAug 19, 2025
How to troubleshoot Biohit mLINE m10 pipette that is out of established specifications?
- O
  Oscar RobertsAug 19, 2025
  If your pipette is out of established specifications, consider the following: * Ensure you are following the operating instructions correctly. * Verify that you are using original tips. * Recalibrate the pipette, as the calibration may have been altered.
S
Suzanne CortezAug 22, 2025
How to fix operating button if it jammed or moves erratically in Biohit mLINE m10?
- R
  Rachel FoxAug 22, 2025
  If the operating button on your Biohit Laboratory Equipment is jammed or moving erratically: * Clean and grease the piston/seal and the tip cone if liquid has penetrated and dried. * Change the filter if the Safe Cone filter has been contaminated. * Apply more grease to the piston and seal if there is an insufficient amount.
F
fraziercynthiaAug 25, 2025
What to do if tip ejector jammed or moves erratically in Biohit Laboratory Equipment?
- C
  carterrobertAug 26, 2025
  If the tip ejector on your Biohit Laboratory Equipment is jammed or moving erratically, remove and clean the ejector collar and tip cone, as the tip ejector collar may have been contaminated.
J
Joshua BirdAug 28, 2025
What to do if the operating button of Biohit mLINE m10 Laboratory Equipment moves erratically?
- D
  David GonzalezAug 28, 2025
  Erratic movement of the operating button can occur for several reasons: * Liquid may have penetrated the tip cone and dried; clean and grease the jammed piston/seal and the tip cone. * The Safe Cone filter may be contaminated; change the filter. * There might be an insufficient amount of grease on the piston and seal; grease accordingly.
C
carloshernandezAug 31, 2025
What to do if tip ejector jammed in Biohit Laboratory Equipment?
- E
  Emily VanceAug 31, 2025
  If the tip ejector is jammed, it might be due to contamination of the tip ejector collar. Remove and clean the ejector collar and tip cone.
J
Julie MorrisSep 3, 2025
How to avoid droplets inside the tip of Biohit mLINE m10?
- A
  Amy BridgesSep 3, 2025
  To avoid droplets remaining inside the tip, use original tips.
M
Mrs. Sandra Jones MDSep 6, 2025
What to do if Biohit Laboratory Equipment is leaking or pipetted volume is too small?
- S
  Shawna JonesSep 6, 2025
  If you're experiencing leakage or the pipetted volume is too small with your Biohit Laboratory Equipment, here's what you can do: * Ensure the tip is firmly attached, as it may be incorrectly attached. * Attach a new tip, as there may be non-uniform wetting of the plastic. * Use original tips, as the tip might be unsuitable. * Clean the tip cone and attach a new tip to remove any foreign particles between the tip and tip cone. * Tighten the tip cone holder if it is incorrectly tightened. * If the issue persists, the pipettor may be damaged. Return it to your Biohit service representative for servicing.
K
Kurt MercadoSep 9, 2025
Why is my Biohit mLINE m10 Laboratory Equipment out of established specifications?
- V
  valdezkathleenSep 9, 2025
  If your Biohit Laboratory Equipment is out of established specifications, consider the following: * Ensure you are following the instructions for correct operation. * Use original tips, as unsuitable tips can cause this issue. * Recalibrate the pipettor, as the calibration may have been altered.
B
Bryan SalasSep 12, 2025
How to prevent droplets left inside the tip of Biohit Laboratory Equipment?
- M
  Meghan RamirezSep 12, 2025
  If you notice droplets left inside the tip of your Biohit Laboratory Equipment, use original tips.