EasyManua.ls Logo

Bissell 1986 - User Manual

Bissell 1986
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
www.BISSELL.com
1
More of a video
person? Look for this
icon and go online
for an instructional
how-to video at
www.BISSELL.com
USER GUIDE
Models 1986, 2007G, 2007H, 2007Q
REVOLUTION
™
PET PRO

Table of Contents

Questions and Answers

  • K
    Karla RoweJul 29, 2025
    Why does my Bissell Vacuum Cleaner have no suction power?
    • M
      Miranda HarperJul 29, 2025
      A loss of suction power in your Bissell Vacuum Cleaner can occur due to several reasons. The dirty water tank may not be seated properly; ensure it's correctly fitted. The tank might be full, so empty it if it has reached the maximum fill line. Check the rubber tab on the dirty water tank to ensure it is sealed tightly. Also, verify that the accessory hose door is closed tightly and locked in place. The nozzle could be clogged with pet hair or debris; use the nozzle clean-out tool. Lastly, ensure the brush roll cover is fully snapped into place.
  • L
    lindaashleyAug 3, 2025
    How to fix no spray through the hose and tool on my Bissell 1986?
    • J
      James SmithAug 3, 2025
      If there is no spray through the hose and tool of your Bissell Vacuum Cleaner, the hose to your machine is not primed or may have lost prime. With the machine OFF and unplugged, remove the Nozzle from the Foot. Place a ballpoint pen in the black cylinder next to the screw. When water bubbles up, remove the pen. Reassemble the Nozzle and hose. Hold the end of the hose below the water level in the tank to prime it. With the Clean Water Tank full of water, the machine OFF and reclined, press the CleanShot button ON and wait for the CleanShot to drain for a few seconds; this will re-prime the machine. Also, the Clean Water Tank may be empty, so refill it. Ensure the Clean Water Tank is seated properly by turning the power OFF and reseating the tank.
  • D
    david99Aug 7, 2025
    How to fix no spray through CleanShot on my Bissell 1986?
    • F
      fordryanAug 7, 2025
      If there is no spray through the CleanShot on your Bissell Vacuum Cleaner, first, ensure the Clean Water Tank is not empty and refill it if needed. Next, check that the Clean Water Tank is seated properly; turn the power OFF, then remove and reseat the tank. Make sure the machine is reclined by pressing the Recline Pedal and bringing the handle down. If the pump may have lost prime, with the machine OFF and unplugged, remove the Nozzle from the Foot. Place a ballpoint pen in the black cylinder next to the screw. When water bubbles up, remove the pen. Reassemble the nozzle before cleaning again.
  • D
    Danielle BaldwinAug 12, 2025
    How to fix reduced or no spray through the foot of my Bissell 1986 Vacuum Cleaner?
    • W
      wallacejosephAug 13, 2025
      If you experience reduced or no spray through the foot of your Bissell Vacuum Cleaner, the Clean Water Tank may be empty, so refill it. Also, the Clean Water Tank may not be seated completely; turn the power OFF, then remove and reseat the tank.
  • V
    Vincent BryantAug 18, 2025
    What to do if my Bissell 1986 has no power?
    • J
      Julie DawsonAug 18, 2025
      If your Bissell Vacuum Cleaner has no power, ensure you are pressing the red Power Button on the left side of the machine, not the Cleaning Mode Switch. Check if the outlet is active by plugging in another device.
  • R
    Rebecca PaulAug 22, 2025
    What to do if my Bissell 1986 Vacuum Cleaner CleanShot continues to spray when the machine is off?
    • A
      Ashley HermanAug 22, 2025
      If the CleanShot on your Bissell Vacuum Cleaner continues to spray when the machine is off, the CleanShot button is not in the off position. Press the CleanShot button to turn it off; the button window will show the color red and a “O” symbol when it is in the off position.

Summary

Important Safety Instructions

Whats in the Box?

Product View

Assembly

Cleaning Formula

Pretreat

Pretreat spots and stains to improve carpet cleaning performance.

Boost

Add Boost carpet cleaning formula enhancers to any formula to increase its effectiveness.

Filling Your Clean Water Tank

Filling Your Clean Water Tank: For Future Use if selecting Antibacterial Formula with EasyFill

Cleaning Your Carpet

Cleaning with Hose & Tool

Cleaning with CleanShot

Using the 2-in-1 Pet Upholstery Tool

Cleaning Area Rugs

Emptying the Dirty Water Tank

Cleaning Machine After Use

Storing Your Machine

Cleaning the Brush Roll & Nozzle

Replacing the Belts & Brush Rolls

Troubleshooting

Warranty

Service

Register Your Product

Parts & Supplies

Bissell 1986 Specifications

General IconGeneral
Model1986
TypeUpright
Brush RollTangle-Free Brush Roll
Pet Hair ToolYes
Power SourceCorded Electric
Voltage120V
Amps7 amps
ColorBlue
Included ToolsCrevice Tool
Special FeaturesEdge-to-Edge Cleaning
Weight18 pounds

Related product manuals