To Next PageTo Next PageWhat to do if my Bissell Vacuum Cleaner has reduced spray or no spray?
If your Bissell Vacuum Cleaner has reduced or no spray, the Clean Water Tank might be empty, so refill it. Ensure the Clean Water Tank is completely seated by turning the power OFF and reseating the tank. If in hose cleaning mode, the pump might have lost prime, so hold the end of the hose below the water level in the tank to prime it.
How to fix a leaking Clean Water Tank on my Bissell Vacuum Cleaner?
If your Clean Water Tank is leaking, it might be overfilled. Ensure the tank has the correct amount of water and formula. With the cap tightly on, hold the tank at an angle over a sink or drain to allow any extra water to pour out. Wipe the tank dry with a cloth. Also, water may be caught in space between the tank and the tank’s handle.
What to do if my Bissell POWERFORCE POWERBRUSH PET XL has no spray through the hose and tool?
If there is no spray through the hose and tool of your Bissell Vacuum Cleaner, the hose to your machine may not be primed. With the machine OFF and unplugged, remove the nozzle from the foot. Place a ballpoint pen in the black cylinder next to the screw. When water bubbles up, remove the pen. Reassemble the nozzle and hose.
How to fix a leaking Dirty Water Tank on my Bissell POWERFORCE POWERBRUSH PET XL?
If the Dirty Water Tank is leaking, the tank ring may not be installed properly. Remove the tank, then remove and reinstall the tank ring.
Why is my Bissell POWERFORCE POWERBRUSH PET XL Vacuum Cleaner losing suction power?
Several factors can cause a loss of suction power in your Bissell Vacuum Cleaner. The tanks might not be seated correctly, so pick up both tanks and reseat them properly. The Dirty Water Tank may be full, so empty it if it has reached the full line. Check the Clean Water Tank and refill it if empty. Ensure the rubber tab on the Dirty Water Tank is sealed tightly and that the Accessory Hose Door is closed securely. The nozzle may be clogged, so use the Nozzle Clean Out Tool. Finally, make sure the nozzle is installed correctly; if not, remove and reinstall it.
Why is there no power in my Bissell POWERFORCE POWERBRUSH PET XL?
If your Bissell Vacuum Cleaner has no power, first make sure you are pressing the power button on the left side of the machine, and not mistaking the cleaning mode switch for the power button. Also, the outlet may not be active, so try plugging in a different device to test the outlet.
General| Type | Upright |
|---|---|
| Cleaning Path Width | 12 inches |
| Power Source | Corded Electric |
| Category | Vacuum Cleaner |
| Filter Type | Washable Filter |
| Tank Capacity | 1.5 liters |
| Surface Type | Carpet, Upholstery |
| Dirt Tank Capacity | 1.5 liters |
| Special Features | EdgeSweep Brushes |
| Included Tools | 3" Tough Stain Tool |
Key safety guidelines for operating the appliance and preventing common hazards.
Proper grounding procedures and electrical safety measures for safe operation.
List and visual identification of all accessories supplied with the BISSELL appliance.
Follow these clear steps and diagrams to assemble your BISSELL PowerForce cleaner.
Overview of recommended BISSELL cleaning formulas for carpets and pet stains.
Using pretreatments and boost enhancers for improved cleaning performance.
Detailed instructions on filling the clean water tank with water and BISSELL formulas.
Step-by-step guide for cleaning carpets and area rugs, including pre-cleaning tips.
How to use the accessory hose and tools for cleaning upholstery and spot treatment.
Instructions for removing, emptying, cleaning, and reattaching the dirty water tank.
Steps to clean the nozzle and ensure the accessory hose door is properly closed.
Guide for cleaning debris and hair from the brush rolls for optimal performance.
Detailed instructions on how to replace the cogged belt and brush rolls.
Recommendations for proper storage of the appliance to prevent damage.
A comprehensive table of common problems, their causes, and effective solutions.
