◈ Self-test
Run the self-test when first setting the printer or when encountering a problem, and
check the following.
• Control Circuit, Mechanisms, Print Quality, ROM Version, and Memory Switch
Settings
If no issue is found with the printer after running the self-test, examine the other
devices or peripherals and software. This function is independent of such other
devices and software.
• Self-Test Instructions
1) Turn the printer power off and close the printer paper cover.
2) Pressing the paper feed button and power button simultaneously turns the
printer on.
3) After printing begins, please release the two buttons.
4) To add a printout of the ASCII pattern, press the paper feed button once more.
5) After the ASCII pattern is printed out, the self-test is automatically terminated.
◈ Product Specifications
Item Description
Printing
Printing Method Thermal printing
Printing Speed
100 mm/sec (Receipt Paper)
80 mm/sec (Linerless Paper)
Resolution 203 DPI
Paper Supply Mode
Easy paper loading
Character Size
Font B: 9 × 17
Font C: 9 × 24
Character Set
English: 95
Expanded Graphics: 128 × 33 pages
International: 32
Barcode
1 Dimension: UPC A, UPC E, CODE 39, CODE 93,
Code 128, EAN 8, EAN 13, ITF, Codabar
2 Dimension: PDF417, DATAMATRIX, MAXI,
QR Code, GS1 DataBar, Aztec
Emulation BXL/POS
Driver
Windows XP(32/64bit) / WEPOS /
2003 Server(32/64bit) / VISTA(32/64bit) /
2008 Server(32/64bit) / 7(32/64bit) / 8(32/64bit)
SDK
Windows XP / WEPOS / 2003 Server /
VISTA / 2008 Server / 7 / 8 / CE 3.0 and later
Paper End, Paper Cover Open
Language User language supported
Paper
Diameter Max. ø40 mm (1.57”) Max. ø39 mm (1.54”)
Width
(2.26” ± 0.2”)
(2.26” ± 0.2”)
※ Note
1) This equipment is indooruse and all the communication hiring are limited to inside
of the building.
2) The switch is the disconnecting device. Turn off switch from any hazard.
◈ Label Printing Function
1. Label Function Setting
Label paper and black mark paper available at the label mode.
• Setting Operations
1) Turn on the printer power.
2) Open the paper cover and press and hold down the paper feed button for longer
than two seconds.
3) After the buzzer tone is emitted, insert paper and close the cover.
4) Repeat the steps above to return to receipt mode.
• Setting Via Memory Switch
1) Please refer to the memory switch changing section of the Commands Manual.
2. Auto Calibration Function
The label printing function requires the recognition of label paper gaps and black
mark paper black bar in order to print.
If label paper gaps are not properly recognized, use the auto calibration function.
• Auto Calibration Instructions
1) Turn the printer power off while in label print mode.
2) Press and hold down the paper feed button and then press the power button.
3) After the following printout is outputted, press the power button to perform auto
calibration.
Select the mode
Auto Calibration: Power Button
Self Test: Feed Button
4) Three pages of label paper are outputted when performing auto calibration.
◈ Peripherals Connection
1. Bluetooth & Wireless LAN Connection
1) The printer can be connected to devices equipped with
Bluetooth communication capacity (PDAs, PCs, etc.).
2) Use the Bluetooth connection function supported by the
device to connect to the printer. The NFC tag built into
the printer enables automatic pairing with devices.
※ Note
The device must support NFC Auto Pairing.
It may display a message that the device cannot be
connecteREVd as NFC Auto Pairing is supported upto the
B/T pairing and the devices must connected manually, but
this is normal.
3) The printer can be connected to other stations, such as
PDAs and PCs supporting
wireless LAN communication in
Ad-hoc mode and AP in Infrastructure mode.
※ Note
Refer to the Bluetooth Wireless LAN Manual for detailed information on its connection.
You can check the Bluetooth environment (authentication, encryption, connection mode) and the
wireless LAN environment (IP, SSID, authentication, encryption) via the self-test page.
2. Interface Cable Connection
1) Open the Interface Cap
2) Connect the interface cable (optional) to the cable
connector of the printer.
◈ Printer Cleaning
If the interior of the printer is dusty, print quality can decline.
In such a case, follow the instructions below to clean the printer.
• Caution
1) Make sure the printer power is turned off before cleaning.
2) Wait for two to three minutes after power-off before head cleaning because the head
part may become very hot during printer operation.
3) Take care not to touch the heating region of the head with your hand while cleaning
the head part.
→ The printer head may be damaged by static electricity.
4) Take care to avoid scratching the head.
5) Clean the printer head periodically if linerless paper is used. Recommended cleaning
period is after consuming ten rolls of linerless paper (100 meters), or more than once
a week. Printing quality may be degraded or printer life may be shortened if the head is
not cleaned periodically.
• Warning
1) Use only the linerless paper that is provided by BIXOLON. Use of other paper voids
product warranty.
◈ Certification
This marking shown on the product or its literature, indicates that i
not be disposed of with other household wastes at the end of its working life.
To prevent possible harm to the environment or people from uncontrolled
waste
disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government off
ice, for details of where and how they
can take this item for environmentally safe recycling. Business users should
contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial w
disposal.
The following Bluetooth mark and
is only applicable to models
with the Bluetooth SIG qualification.
To Next Page
Loading...
