Black & Decker LST522 User Manual

ENGLISH
12
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with yourproduct.
Repairs
The charger and batteries are notserviceable. There are no
serviceable parts inside the charger or batterypack.

WARNING: To assure product SAFETY
and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a BLACK+DECKER factory
service center or a BLACK+DECKER‑authorized service center.
Always use identical replacementparts.
Rewinding Spool from Bulk Line (Fig.S–V)
Use Only 0.065" (1.65 mm) Diameter, Round
Line
Bulk line is also available for purchase from your
localretailer.
NOTE: Hand wound spools from bulk line are likely to
become tangled more frequently than BLACK+DECKER
factory wound spools. For best results, factory wound spools
arerecommended.
1. Remove battery pack fromappliance.
2. Remove the empty spool from the appliance as
described in Replacing SpoolAssembly.
3. Remove any remaining cutting line from thespool.
4. Make a fold at the end of the cutting line
25
at about
3/4" (19 mm). Feed the cutting line into one of the line
anchoring slots
27
.
5. Insert the 3/4" (19 mm) end of the bulk line into the
spool hole
30
in the spool adjacent to the slot. Make sure
the line is pulled tight against thespool.
by BLACK+DECKER on this trimmer/edger. Serious injury or
product damage mayresult.
Reload nylon line (either bulk or prewound replacement
spool) as shown in thismanual.
USE ONLY 0.065" (1.65 mm) DIAMETER ROUND NYLON
MONOFILAMENT LINE. Do not use serrated or heavier gauge
line, as they will overload the motor and cause overheating.
This line is available at your local dealer or authorized
servicecenter.
1. Remove battery pack fromappliance.
2. Press the release tabs
20
on the spool cap
19
, and
remove the spool cap from the spool housing
11
.
3. For best results, replace spool with BLACK+DECKER
ModelAF-100.
4. If lever
22
in base of housing becomes dislodged,
replace in correct position before inserting new spool
intohousing.
5. Remove any dirt and grass from the spool cap and
spoolhousing.
6. Unfasten the end of the cutting line
25
and guide the
line into the eyelet
28
.
7. Take the new spool
26
and push it onto the boss
23
in
the housing. Rotate the spool slightly until it isseated.
8. The line should protrude approximately 5-3/8" (136mm)
from thehousing.
9. Align the release tabs on the spool cap with the line
anchoring slots
27
in the spoolhousing.
10. Snap the spool cap
19
back on by depressing release
tabs
20
and pressing it into the spoolhousing
11
until it
snaps securely intoplace.
NOTE: Make sure that cover is fully positioned. Listen for
two audible clicks to ensure both release tabs are correctly
located. Power the appliance on. In a few seconds or less
you’ll hear the nylon line being cut automatically to the
properlength.
NOTE: Other replacement parts (guards, spool caps, etc.)
are available through authorized service centers. To find
your local service location call: 1-800-544-6986 or visit
www.blackanddecker.com.
Accessories

WARNING: Since accessories, other
than those offered by BLACK+DECKER, have not been
tested with this product, use of such accessories with this
product could be hazardous. To reduce the risk of injury, only
BLACK+DECKER recommended accessories should be used
with thisproduct.
Recommended accessories for use with your product
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact BLACK+DECKER.
Call1-800-544-6986.
Cleaning

WARNING: Blow dirt and dust out of all
air vents with clean, dry air at least once a week. To minimize
the risk of eye injury, always wear ANSI Z87.1 approved eye
protection when performing thisprocedure.

WARNING: Never use solvents or other
harsh chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into aliquid.
MAINTENANCE

WARNING: To reduce the risk of
serious personal injury, turn unit off and remove
the battery pack before making any adjustments or
removing/installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental start‑up
can causeinjury.
Your BLACK+DECKER power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regularcleaning.
6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on neatly
and in layers. Do notcrisscross.
7. When the wound cutting line reaches the recesses
29
,
cut theline.
8. Fit the spool onto the appliance as described in
Replacing SpoolAssembly.

Black & Decker LST522 Specifications

General

Power Source	Battery
Voltage	20 V
Cutting Swath	12 inches
Line Diameter	0.065 inches
Feed System	Automatic Feed Spool (AFS)
Variable Speed	Yes
Battery Type	Lithium Ion