8
ENGLISH
(Original instructions)
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
The accessories supplied with your sander depend upon the
model that you have purchased. If you require an accessory
that is listed below but is not supplied with your sander please
visit our website at www.blackanddecker.eu
Item Description Purpose
Large detail sanding base (4). For medium to large
areas. The large detail
base can be used to sand
into corners and to the
edge of the workpiece.
Random orbit sanding base
(3).
For large areas. The
random orbit base can be
used for curved surfaces
and when you need a
high-quality nish.
Detail nger (6). For small hard-to-reach
areas. The detail nger
can be used for light
sanding and for sanding
into corners.
Hints for optimum use
u For user comfort, the tool can be operated with one or
two hands (g. L, M, N). Do not place your hands over the
ventilation slots.
u Do not exert too much pressure on the tool.
u Regularly check the condition of the sanding sheet.
Replace when necessary.
u Always sand with the grain of the wood.
u When sanding new layers of paint before applying
another layer, use extra ne grit.
u On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
ne grit for a smooth nish.
u Consult your retailer for more information on available
accessories.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Before performing any maintenance on the tool,
remove unplug the charger before cleaning it.
u Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
BEW200
Input voltage V
AC
230
Power input W 200
No-load speed min
-1
12000
Weight kg 1.40 (with detail base),
1.34 (with ROS base)
Level of sound pressure according to EN 62841:
Sound pressure (L
pA
) 82.5 dB(A), uncertainty (K) 3 dB(A)
Sound power (L
WA
) 93.5 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 62841:
(a
h
) 9.8 m/s
2
, uncertainty (K) 1.5 m/s
2
EC declaration of conformity
MACHINERY DIRECTIVE
%
BEW200 Sander
Black & Decker declares that these products described under
“technical data” are in compliance with:
2006/42/EC, EN62841-1:2015, EN62841-2-4:2014.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact Black &
Decker at the following address or refer to the back of the
manual.
To Next Page
Loading...
