INSTALLATION
Recommendations
*
Carefully choose the mounting location so that the unit won’t interfere with normal driving.
*
Avoid mounting locations where the unit would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where
it would subject to dust, dirt or excessive
vibration
*
The Illustration below shows a
typuzal
installation, however, you may need to adjust the
s’tstaltatlon.
depending on the unit. If you have questions or need additional installation
hardware, consult your Blaupunkt dealer.
l
Make sure the uniiis firmly anchored (preferably at both front and back)
and does not vibrate.
Mounting the Unit in a Japanese Car
You may have
difficulty
mounting
this unit in some Japanese cars.
In this case, consult your Blaupunkt dealer.
Removing the Unit
Use the Release Keys as shown below. Keep them in a safe place in case
in the future.
MAINTENANCE
Mounting The Unit in Most Dashboards
1
Install the Sleeve in the dashboard.
2 Select and bend the appropriate tabs to hold the sleeve firmly in place.
3 A.
Attach the Mounting Strap to the underside of the dashboard, using screw.
B.
Attach the back of the unit to the mounting strap using the support stem bolt and hardware.
Bend these tabs
You need them
1
f-gq
@,
1
Fuse Replacement
When
replaclng
the fuse. be sure to use one with the correct amperage,
whtch
will be slated on the fuse case. Never use a fuse that has a stated amperage exceeding the one
supplied for this
unit.
as this could cause
malfunction
and serious damage to the
unit.
SPECIFICATIONS
Audio Power Specifications
Power Output and Total Harmonic Distortion: 10 watts per channel minimum continuous average output into 4 ohms, 4 channels driven, from 30-15.000 Hz with no more than 1%
total
harmonic
dIstortIon
.
Other
Specifications
Tuner
FM
Tuning Range:
IntermedIate
Freouencv:
FM Mono Sensitiiity:
~’
Selectivity:
Signal-to-Noise Ratio:
Harmonic distortion at 1
kHz:
Separation:
Frequency Response:
bM
.
.
.
Tuning Range:
Seek lo
sensitivitv
Seek sensitivity:
’
Intermediate Frequency:
Signal-to-Noise Ratio:
530
-
1,710
kHz
55
dBpV
35
dBpV
45”
kH,
_
_
._
45
dB
Design and specifications subject lo change
withouf
notice.
87.5
-
107.9
mHz
10.7
mHz
18
dBf
75
dB
at 400
kHz
85
dB
(stereo), 70
dB
(mono)
0.7% (stereo), 0.5% (mono)
30
dB
30-l 5,000 Hz
f
3
dB
. .
Audio
Speaker Impedance:
Maximum
imp
Power:
RMS Power:
Bass Control:
Treble Control:
Cassette
Signal-to-Noise Ratio:
Tape Wow and Flutter:
Tape Frequency Response:
General
4-8 ohms
30 Watts x 4 (at 4 ohms)
iowansx4
+iO
dB
@
100 Hz
*lOdB@
10kHz
53
dB
0.10%
50-l 5,000 Hz
*
3
dB
Dimensions
(w/o
proiectinq
parts/controls):
178
x
50
x
153 mm
Mass:
Power Requirement (neg. gmd.):
Operating Temperature:
Supplied Accessories:
7
x
2
x
6 in.
Approx. 1.4 kg (3.0 lb.)
12 V DC car battery
15°F to
12O’F.
-10°C to 50°C
l
Untt
l
Faceolate
r
l
Mounting Hardware
*
DIN Sleeve
l
Owner’s Manual
In
English, French, Spanish and Portuguese
To Next Page
Loading...
Need help?
General
