INSTALLATION
Recommendations
l
Carefully choose the mounting location so that the unit won’t interfere with normal driving.
l
Avoid mounting locations where the
unit
would be subject to high temperatures, such as from direct sunlight or hot air
from
the heater, or where it would subject to dust, dirt or
excessive vibration.
l
The illustration below shows a typical installation, however, you may need to adjust the installation, depending on the unit. If you have questions or need additional installation
hardware, consult your Blaupunkt dealer.
l
Make sure the unit is firmly anchored (preferably at both front and back) and does not vibrate.
Mounting Hardware
Mounting The Untt In Most Dashboards
1 Install the Sleeve (1) in the dashboard.
2 Select and bend the appropriate tabs to hold the sleeve
ftnnly
in place.
3
A.
Attach the Mounting Strap (2) to the underside of the dashboard, using screw.
B.
Attach the back of the unit to the mounting strap using the support stem bolt and hardware.
Mounting the
Unft
In a
Jspaneae
Car
You may have difficulty mounting this unit in some Japanese cars.
In this case, consult your Blaupunkt dealer.
Removing the Untt
Use the Release Keys as shown below. Keep them In a safe place In case
you need them In the future.
Fuss Replacement
When replacing the fuse, be sure to use one with the correct amperage,
which will be stated on the fuse. Never use a fuse that has a stated
amperage exceeding the one supplied for this unit, as this could cause
malfunction and serious damage to the unit,
Dash
Bend these tabs
SPECIFICATIONS
Audio Power
Stmclflcatlona
Power Output and Total Harmonic Distortton: 13.5 watts per
channel minimum continuous average output Into 4
ohms, 4
channels driven.
fmm
30-15,COO
Hz with no more than 1%
total harmonic distortion.
Dther %eclflcatlona
Tuner
\
FM
Tuning
Rage
675-1079MHz
67 5 106 0 MM
IRW
435X
onlvl
Intermediate Frequency:
10.7MHz
I.
FM Mono Sensitivity:
6
dBf
Seek Sensitivity
22
dBf
Selectivity:
60
dB
at 400
kHz
Signal-to-Noise Ratio:
Harmonic Distortion at 1
kHz:
70
dB
(stereo). 75
dB
(mono)
Separation:
07;B(sterec).
0.5% (mono)
Frequency Response:
30-15,ooO
Hz
*
0.75
dB
Design and specifications subject to change without notice.
AM
Tunmg
Range
Seek
Sens!tiv!ty
lnlermedrate
Frequency
SIgnal-to-Norse
Ratlo
Audio
Speaker Impedance
MaxImum
Amp Power
RMS Power
Bass Control
Treble Control
Loudness
Preamp Outputs
Preamp Output Voltage
(
:D Player
530-1.7lOkHz
:innal-h-No&
R&o:
*‘“;l;;;
Range:
&
63
dB
531
-
1.502
kHz
(RPD
435X only)
31
dBpV
90dB
450
kHz
Frequency Response:
5-20,COO
Hz
f
3 d6
I
50
dB
620,000 Hz
f
1
dB
Harmonic Distortion: .Ol%
4.6ohms
4
x
35 Watts (at 4 ohms)
4
x 17 5 Watts (at 4 ohms)
+lOdBOlOOHz
tl0
dB
@
10 ktiz
tlOdB01100Hz
&+7dB@0kHz
2.CH
RCA
1.5 volts maximum
8
100%
Modulation with
<
1% Total
Harmonic Distortion
General
Drmensions
(w/o
projecting parts/controls):
176x50x155.5mm
7 x 2 x 6 in.
Mass:
Approx. 1.4 kg (3.0 lb.)
Power Requirement
(neg. gmd.):
12 V DC car battery
Operating Temperature:
15°F to 120°F. -10°C to 50°C
Supplied Accessories:
9
Unit
. Faceplate
l
DIN Sleeve
l
Mounting Hardware
l
Owner’s Manual in English,
French, Spanish and Portuguese
To Next Page
Loading...
