Note: Make sure that the
face
is inserted right side up. Do not press against the display window. Do not press hard against the face when attaching it to the chassis, it may be easily
attached with gentle pressure Do not expose the face to direct sunlight, heat sources such as hot air ducts or leave it in a humid place. Never leave it on the dash board of a vehicle
parked in direct sunlight, where there may be a considerable rise in temperature inside the vehicle.
Afffxing
Faceplate For Retail Display:
The faceplate can be affixed to the unit’s chassis, which is desirable for a retail display, for example.
This
should only be done in situations whom the unit can be accessed
from behind the mounting surface. Once the faceplate is affixed, the
mlease
keys cannot
ba
used to remove the chassis.
To
afffx
the faceplate, obtain the small bolt
(M2.6~10)
from hardware pack and
drive
it into the upper hole at the left of the chassis using a Phillips screwdriver. The
bolt
will
self-thread
the hole. (See’
rn
Fig.2.)
ELECTRICAL CONNECTIONS AND INSTALLATION
@/~?#&*~@I
To avoid the aggravation of costly
mrstakes
and serious damage that could make you feel this way, please carefully read all of the instructions before you begin
Carefully follow all instructions. You’ll be glad you did!
GENERAL
RECOMMENDATTONS
l
If you’re not
confident
that you can install the unit correctly, have it installed by a qualified
Blaupunkt
installation
technician.
l
Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC).
l
Be sure to detach the faceplate before you start to connect or
mstall
the unit.
l
We recommend making and testing all electrical
connecttons
before installing the unit.
Connact
the leads (wires) according to instructions and diagram below.
ELECTRICAL
CONNECTtON
INSTRUCTIONS
1.
2.
3.
4.
::
7
8
9
10
11
12
&connact
the vehicle battery’s negative terminal before making connections.
Connect the speakers and/or external amplifiers (if you have any) following the guidelines in the SPEAKER CONNECTION section below.
Connect the blue (trigger output) lead to the amplifier’s trigger input terminal and/or antenna motor trigger input terminal (if you have either or both of these Items). The combined
total amperage required for triggering the antenna motor
and/or
amplifier must not exceed
100
mA.
DO NOT connect the blue lead to the antenna’s
and/or
amplifier’s power
supply input.
Connect the black (power ground) lead to a grounded metal part on the vehicle. We recommend grounding all audio system black ground leads (head unit, external amplifier,
etc.) to a common grounding point, preferably a non-painted surface under the instrument panel.
Connect the yellow (constant power) input lead to a source of constant battery power, preferably a terminal to an appropriate slot in the fuse box.
Connect the red (turn-on power) input lead only afler the other leads are connected. Be sure to connect the red lead to a positive (+) 12 Volt power terminal that is energized only
when the ignition key is set to the on position or accessory position.
Cover the ends of any unused leads with electrical tape. This
will
prevent them from touching the vehicle or each other and causing a short-circuit and damage lo the radio Or vehicle.
Reconnect the vehicle’s battery.
connect
me
antenna
plug.
Verify that no fuses have blown.
Plug the harness into
Ihe
unit.
Attach the faceplate and
lest
the unit.
Once the
connectrons
have been successfully made, you can
begln
to mount the
unit
SPEAKER
CONNECTtONS
The
unrt’s
Dual-Level Fader allows you to lade between the front and the rear channels using either the from and/or rear speaker leads
and/or
the rear preamp outputs, providing you
tremendous
flexibrlity
in configuring your speaker arrangement
l
You can connect a speaker (regular,
co-axral
or
td-axral
speakers or component speaker system, all hereafter referred to simply as ‘speaker”) to each of the
units’
four pairs of
speaker leads.
l
You can connect the 2 RCA preamp outputs to
mbltiple
external amplifiers and power multiple speakers or speaker
systems through the amplifiers. (Blaupunkt
ampkfters
and speakers available separately. Call l-800-950-2528
for
product brochure and/or dealer referral.)
l
You can use a combination of these two methods.
Connecting the Speaker Leads
To prevent short circuits or
sertous
damage to the unit and/or speakers:
l
Connect the speaker leads only as indicated in the wiring diagram.
l
Only use speakers that have impedance ratings of 4 ohms or
hrgher
and have power-handling capabilities greater than
the head unit’s stated power level.
l
The unit’s internal amplifier is designed to handle a
4-ohm
load on each pair of speaker leads.
l
DON’T connect two speakers to a single pair of speaker leads (“in parallel”) unless both speakers each have at least 8
ohms impedance
l
DON’T connect the left and
right
speaker leads to each other or to the same speakers.
l
DON’T connect the front and rear speaker leads to each other or to the same speakers.
l
DON’T connect the negative speaker leads to each other.
l
DON7 connect the positive speaker leads to each other.
l
DON’T connect any active speakers (with built-in amplifiers) to the speaker leads or unless the speaker’s or amplifier’s
manual states that this is OK.
To Next Page
Loading...
