To Next PageTo Next Page
Need help?Do you have a question about the Blaze 400 G and is the answer not in the manual?
General| Heating Element | Ceramic |
|---|---|
| Adjustable Thermostat | Yes |
| Overheat Protection | Yes |
| Fan | Yes |
| Voltage | 120V |
General hazards related to heater operation, including fire and burn risks.
Failure to comply can result in death, injury, or property damage from fire, explosion, or CO poisoning.
Not for home or recreational vehicle use; requires adequate ventilation.
Emphasizes reading instructions before operating the heater for safe and correct use.
Details approved standards and primary use as a temporary construction heater.
Highlights the need for adequate ventilation and protection from water exposure.
Installation must comply with local, national, and specific fuel gas codes and regulations.
Specifies minimum distances from propane cylinders to prevent hazards.
Details approved fuel oil types and prohibitions for oil-fired operation.
Emphasizes qualified service personnel and proper installer training.
Outlines installation codes for Canada and wiring compliance.
Warns about combustion air issues and lists key heater specifications.
Step-by-step guide for connecting LP cylinders safely, including leak testing.
Guidelines for storing LP cylinders and requirements for gas piping.
Instructions for connecting the Blaze 400 D to an external fuel tank.
Guidelines for operating the Blaze 400 G on propane or natural gas, including conversion.
Specifies the type of approved hoses for fuel supply connections.
Details required voltage, phase, and wire gauge for installation.
Specifies grounding requirements according to NEC and CSA codes.
Lists voltage, amperage, and fuse size for the heater's electrical system.
Wiring diagram for the Blaze 400G using a Beckett CG10-24 NG/LP burner with axial fan.
Wiring diagram for the Blaze 400G using a Beckett CG10-24 NG/LP burner with E fan.
Wiring diagram for Blaze 400G with Beckett CG10-24 NG/LP burner and R fan.
Wiring diagram for Blaze 400G with Riello G400 NG/LP burner and axial fan.
Wiring diagram for Blaze 400G with Riello G400 NG/LP burner and E fan.
Wiring diagram for Blaze 400G with Riello G400 NG/LP burner and R fan.
Wiring diagram for Blaze 400D with Beckett CF375 oil burner and axial fan.
Wiring diagram for Blaze 400D with Beckett CF375 oil burner and E fan.
Wiring diagram for Blaze 400D with Beckett CF375 oil burner and R fan.
Wiring diagram for Blaze 400D with Riello F10 oil burner and axial fan.
Wiring diagram for Blaze 400D with Riello F10 oil burner and E motor.
Wiring diagram for Blaze 400D with Riello F10 oil burner and R motor.
Detailed steps for heater operation in ON and BYPASS modes.
Step-by-step instructions for safely starting the heater.
Step-by-step instructions for safely stopping the heater.
Steps to troubleshoot and resolve starting issues, including reset procedures.
Important safety advice regarding operation, maintenance, and environmental factors.
Specifies the electrical load and requirements for the heater.
Guidelines for installation, air, and electrical supply based on local codes.
Specifies required minimum clearances from the heater to surrounding objects.
Instructions for flue connections, with cautions on high flue temperatures.
Visual representation of required installation clearances for the heater.
Specifies the maximum lengths for supply and return ducts.
Guidelines for regular maintenance and inspection of hose assemblies.
Procedures for checking and maintaining the temperature controller and thermocouple.
Inspection of electrical connections, fan, and motor for proper operation.
Maintenance steps for gas train, heat exchanger, and fuel filter for oil operation.
Maintenance for flame detector and ensuring unobstructed airflow for combustion.
Table correlating LED flashes with cad cell resistance for diagnostics.
Procedures for adjusting electrode spacing and performing combustion tests.
Guidelines for adjusting combustion air for optimal performance and efficiency.
Details on pressure, nozzle, head, and air settings for various models.
Specific instructions for adjusting the air shutter and band on the Beckett CG10-24.
Reiterates the danger of insufficient combustion air.
Labeled diagram identifying key components of the Riello G400 burner.
Instructions for adjusting the manual air gate for combustion air regulation.
Labeled diagram identifying all components of the Riello F10 oil burner.
Procedures for removing and installing the burner drawer assembly.
Critical dimensions and verification for setting the electrodes correctly.
Steps for adjusting the turbulator for optimal performance.
Instructions for adjusting the air gate on the Beckett CF375 oil burner.
Comprehensive guide for optimizing combustion air for the Beckett CF375.
Step-by-step guide for setting gas firing rates and air adjustments.
Step-by-step guide for setting oil firing rates, pump pressure, and air.
How to connect and operate the heater with a thermostat for temperature control.
Labeled diagram showing major components of the Beckett CG10-24.
List of major components with descriptions and part numbers.
Replacement parts for Beckett ignition transformer and primary control.
Replacement parts for Beckett motor, blower wheel, and gas valve.
Detailed list of spare parts for the Riello G400 burner.
List of spare parts for accessories and gas train components.
Labeled exploded view of Riello F10 oil burner components.
Comprehensive list of spare parts for the Riello F10 oil burner.
