DESCALING
IMPORTANT: The company will not be held responsible for intervention covered
by a warranty for espresso machines that are broken or do not work correctly
due to the fact that the user has not carried out the descaling procedure.
Switch the Power button (K) to turn the unit OFF “o”.
Switch the Power button (K) to ON “ —”.
Fill the water tank (M) with 0.8 L warm tap water and place back on the
espresso machine.
Pour ExpressoKleen 40g sachet (available on bluepod.com.au) into
water tank. Stir until disolved. Take care not to splash. Follow the
safety directions on the packet
Place a large cup on the drip tray grid (J). Press and release the brew-
button (C) twice.
Remove the water tank (M) and rinse thoroughly. Fill the water tank (M)
with 0.8 L warm tap water and place back onto the espresso machine.
After 10 minutes press and release the brew button ‘Long’ twice to
run the remainder of the water through the machine. Repeat with
remainder of water.
To rinse run this full tank of water through the espresso machine by
double pressing and releasing brew button (C) 2 times repeatedly.
WARNING
Any traces of lime scale (naturally present in the water) may seriously
compromise correct operation of the machine. The manufacturer
recommends descaling regularly, every 3 to 6 months.
TROUBLE SHOOTING
No function.
Little or no froth is being produced.
Coffee is not hot enough
The indicator light will illuminate,
but espresso does not flow.
Water under the machine.
The espresso machine is
whistling softly.
Produced little or no Crema.
The water does not flow through the
espresso dispensing nozzle (L).
The brew button (C+D+E) starts
flashing for a long time. When is the
espresso machine ready for use?
The espresso capsule does not fall
automatically into the capsule container
(H), when I open the lever (A).
The espresso capsule does not insert
correctly.
What are the espresso machine
default settings?
What happens if another key is
pressed during distribution of the
brew cycle.
Make sure the power cord is properly inserted into the unit and wall
outlet and the On/Off button (K) on the left of the machine is turned
“on”.
Remove pin (O), wipe clean and replace.
Heat your cup prior to use by filling with hot tap water. Let it rest for 10
seconds and then empty prior to making coffee.
The espresso dispensing nozzle (L) is clogged. The loaded espresso
capsule can be damaged. Wait for a short period of time, before
opening the lever and then try with a new capsule.
Make sure, that the lever (A) is closed.
The capsule container may be full and should removed from the
unit for at least 5 seconds to reset the counter and empty the used
capsules.
Make sure that the water tank (M) is installed correctly. CAUTION:
When refilling the water tank (M), always turn off the power, and then
remove the tank and fill it. Otherwise water may leak from the back
of the unit.
This is not a fault, but normal action of the pressure control valve.
Coffee has natural occurring oils which may clog the espresso nozzle.
To clean, regularly run a brew cycle with water only.
Coffee has natural occurring oils which may clog the espresso nozzle.
To clean, regularly run a brew cycle with water only.
The espresso machine takes approximately 70 seconds to heat up.
The capsule container (H) may be full. Please empty it or make sure
the capsule lever is fully open.
The capsule container (H) may be full. Please empty it or make sure
the capsule lever is fully open.
The One Touch Barista Capsule System is preprogrammed with four
default settings. A single press on brew button (C) will deliver a 40
ml espresso. A double press on brew button (C) will deliver a 180ml
lungo. A single button press for brew button (D) will deliver a delicious
cappuccino and a single button press for brew button (E) will delivery
a rich cafe latte.
Coffee distribution is interrupted in advance.
PH: 1800 800 255
bluepod.com.au
PH: 1800 800 255
bluepod.com.au
To Previous Page
Loading...