What does E2 code mean on my Blyss Air Conditioner?
If the 'E2 Code' appears on your Blyss Air Conditioner, it means the water tank is full during cooling. To resolve this, simply take off the rubber stopper and empty the water tank.
Why is my Blyss A018I-09C Air Conditioner not cool enough?
If your Blyss Air Conditioner isn't cooling effectively, ensure all windows and doors are closed to prevent warm air from entering. Remove any heat sources from the room. Check that the exhaust air hose is properly connected and not blocked. Also, verify that the temperature setting isn't too high, and make sure the air inlet is clean and unobstructed.
What to do if my Blyss Air Conditioner does not start?
If your Blyss Air Conditioner unit doesn't start when you press the on/off button, it could be due to a couple of reasons. First, check if the water full indicator lamp is blinking, indicating a full water tank; if so, empty the tank. Secondly, if you are in cooling mode, the room temperature might be lower than the set temperature. In this case, try resetting the temperature.
What to do if my Blyss A018I-09C Air Conditioner shows E4 code?
If your Blyss Air Conditioner displays the 'E4 Code', it indicates that the water tank is full during heating. Please empty the water tank to resolve this issue.
What to do if the water full indicator lights up too often on my Blyss A018I-09C?
If the water full indicator on your Blyss Air Conditioner lights up frequently, even shortly after you've drained it, the water splash motor might be damaged. Consider repairing or replacing it.
Why is my Blyss Air Conditioner so noisy?
If your Blyss Air Conditioner is excessively noisy, first check whether the unit is placed on a flat, level surface. If it's not, try to reposition it. However, if the noise sounds like flowing refrigerant, this is normal.
What does E0 code mean on Blyss A018I-09C?
If your Blyss Air Conditioner displays an 'E0 Code', it indicates a failure of the room temperature sensor. You can replace the sensor, but the unit can still operate without it.
What does E1 code mean on my Blyss A018I-09C?
If your Blyss Air Conditioner shows an 'E1 Code', it means the condenser temperature sensor has failed. The solution is to replace the condenser temperature sensor.
What does E3 code mean on my Blyss A018I-09C Air Conditioner?
If your Blyss Air Conditioner displays an 'E3 Code', it indicates that the evaporator temperature sensor has failed and needs replacing.
Lists and illustrates all included parts of the air conditioner unit.
Details the additional items and tools needed for proper installation and operation.
Essential initial steps and warnings before first use.
Key precautions against fire, electric shock, injury, and property damage.
Guidelines for safe installation, ventilation, and storage of the appliance.
Methods and precautions for detecting refrigerant leaks.
Guidelines for safely recovering and disposing of refrigerants.
Instructions for optimal placement and maintaining required clearances around the unit.
Key restrictions on where and how the appliance should be used, including child safety.
Specifies the optimal temperature range for unit performance.
Steps for preparing the unit before use, including stabilization.
Detailed instructions for safely replacing the mains plug and fuse.
Comprehensive technical details for various models of the air conditioner.
Step-by-step solutions for common operational issues and error codes.
Explanation of error codes and recommended actions for unit malfunctions.
Instructions for installing the window slider kit for exhaust hose.
Steps for temporarily setting up the exhaust hose connection.
Guidance on installing the exhaust hose through a wall opening.
Instructions for setting up continuous drainage for the unit.
General| Cooling power | 9000 BTU |
|---|---|
| Cooling area | up to 20 m² |
| Power Supply | 220-240V, 50Hz |
| EER | 2.6 |
| Air Flow | 350 m³/h |
| Noise Level | 65 dB |
To Next Page
