BodyCraft XFT - Product Assembly - Step 11: Top Cable Routing; Attach Top Cable to Adjuster Frame; Mount Pulleys and Route Top Cable (T2-T14); Mount Pulleys to Connector Frame (T15-T20)

18
ProductAssembly STEP
BoltEndSteelBallEnd
 TOPCABLE(56)
1.RefertoFigT1.ScrewtheBoltEndoftheTopCable(56)intotheAdjusterFrame(24).
2.RefertoT2.Mounta90mmPulley(52)usingone3/8”X1-3/4”HexBolt(98)andone
3/8”NylonNut(131)totheTopFrame(13).
3.RefertoT3.MounttheT3114mmPulley(51)usingone3/8”X1-3/4”HexBolt(98)
andone3/8”NylonNut(131)totheRightTopPanel(22R).
4.RefertoT4.GuidetheTopCable(56)troughtheRightTopPanel(22R)overa90mm
Pulley(52)usingone3/8”X3”HexBolt(95),two3/8”Washers(118)andone3/8”
NylonNut(131).
5.RefertoT5.Mounta90mmPulley(52)usingone3/8”X1-3/4”HexBolt(98)andone
3/8”NylonNut(131)totheDoublePulleyBlock(36)andguidetheTopCable(56)
alongunderneaththe90mmPulley(52).
6.RefertoT6.Mounta114mmPulley(51)usingone3/8”X1-3/4”HexBolt(98)andone
3/8”NylonNut(131)totheRightTopPanel(22R).
7.RefertoT7.GuidetheTopCable(56)troughtheTopFrame(13)overa90mmPulley
(52)usingone3/8”X1-3/4”HexBolt(98)andone3/8”NylonNut(131).
8.RefertoT8.Mounta90mmPulley(52)usingone3/8”X1-3/4”HexBolt(98)andone
3/8”NylonNut(131)tothePulleyBlock(37).
9.RefertoT9,T10.GuidetheTopCable(56)troughtheTopFrame(13)overa90mm
Pulley(52)usingone3/8”X1-3/4”HexBolt(98)andone3/8”NylonNut(131).
10.RefertoT11.Mounta90mmPulley(52)usingone3/8”X1-3/4”HexBolt(98)and
one3/8”NylonNut(131)totheDoublePulleyBlock(36)andguidetheTopCable
(32)alongunderneaththe90mmPulley(52).
11.RefertoT12.GuidetheTopCable(56)troughtheLeftTopPanel(23L)overa90mm
Pulley(52)usingone3/8”X3”HexBolt(95),two3/8”Washers(118)andone3/8”
NylonNut(131).
12.RefertoT13.Mounta90mmPulley(52)usingone3/8”X1-3/4”HexBolt(98)and
one3/8”NylonNut(131)totheRightCinnecorFrame(13)andguidetheTopCable
(32)alongunderneaththe90mmPulley(52).
13.RefertoT14.Mounta90mmPulley(52)usingone3/8”X1-3/4”HexBolt(98)and
one3/8”NylonNut(131)totheBaseFrame(1).
14.RefertoT15,T16,T17,T18.Mountfour90mmPulley(52)usingthree3/8”X2-1/4”
HexBolts(96),six3/8“Washers(118),oneM6Washer(125),oneM6X12LRound
Screw(109)totheConnectorFrame(15).
15.RefertoT19,T20.Mounttwo90mmPulley(52)usingtwo3/8”X2-1/4”HexBolts
(96),four3/8“Washers(118).
16.RefertoL21.GuidetheTopCable(56)downwardsandconnectthesteelballendof
thecabletotheConnectorFrame(24).
NOTE:Itisrecommendthatyoustudythecableroutingoverview
beginningwithT1beforefollowingthestepsbelow.
11