BOMANN EBK 960 - Installation, Appliance Equipment, and Safety Requirements; Installation Safety and Clearance

•
Do not use harsh abrasive cl
surface.
The glass can be scratched or destroved.
•
Do not try to repair the appliance on your own. Always contact an authorized
technician. If the supply cord is damaged, it must be replaced by the
er, its service agent or similarly qualified persons in order to avoid a hazard.
Unpacking the Appliance
Unpacking the ApplianceUnpacking the Appliance
Unpacking the Appliance
•
Remove the appliance from its packaging.
•
Remove all packaging material, such as foils, filler
and cardboard packaging.
•
To prevent hazards, check the appliance for any
transport damage.
•
In case of damage, do not put the appliance into
operation. Contact your distributor.
NOTE
NOTENOTE
NOTE:
::
:
Production residue or dust may have collected on the
appliance. We recommend cleaning the appliance
according to chapter “Cleaning”.
Appliance Equipment
Appliance EquipmentAppliance Equipment
Appliance Equipment
Hob arrangement
Hob arrangementHob arrangement
Hob arrangement
NOTE
NOTENOTE
NOTE:
::
:
The listed
power settings can vary depending on the
material and/or size of
the cookware.
1
11
1
Control panel
2
22
2 Ø18 c
m / 2000 W
3
33
3 Ø16 c
m / 1500 W
4
44
4 Ø18 c
m / 2000 W
5
55
5 Ø16 c
m / 1500 W
De
DeDe
Delivery scope
livery scopelivery scope
livery scope
installation material: 4 x mounting
bracket, 4 x fixing
screw
5
Do not use harsh abrasive cl
eaners or sharp metal objects for cleaning the glass
The glass can be scratched or destroved.
Do not try to repair the appliance on your own. Always contact an authorized
technician. If the supply cord is damaged, it must be replaced by the
er, its service agent or similarly qualified persons in order to avoid a hazard.
Unpacking the Appliance
Unpacking the ApplianceUnpacking the Appliance
Unpacking the Appliance
Remove the appliance from its packaging.
Remove all packaging material, such as foils, filler
To prevent hazards, check the appliance for any
In case of damage, do not put the appliance into
operation. Contact your distributor.
Production residue or dust may have collected on the
appliance. We recommend cleaning the appliance
Appliance Equipment
Appliance EquipmentAppliance Equipment
Appliance Equipment
power settings can vary depending on the
the cookware.
Control panel
m / 2000 W
m / 1500 W
m / 2000 W
m / 1500 W
bracket, 4 x fixing
Installation
InstallationInstallation
Installation
WARNING:
WARNING:WARNING:
WARNING:
The installation
and the connection to the main power
may only be performed by an authorized specialist.
CAUTION
CAUTIONCAUTION
CAUTION:
::
:
• The worktop
, the cabinet, veneers
ings, used
adhesives etc. must be sufficient
resistant.
• The appliance
must be installed so that heat can
be dissipated.
Air inlet (D) and
not be blocked.
•
The appliance conforms to the heat insulation
class Y, i.e. only one side of the appliance may be
installed near higher kitchen furniture or walls.
•
The distance between the hob and an extractor
hood must be at least as
instructions of the extractor hood!
•
Below the cutout must remain a minimum di
tance (B). In this area are not allowed heat
sensitive objects (cabinet, drawer, etc.). Possibly
existing sidewalls or drawer boxes must be sawed
accordingly or removed.
• Keep safety distances
; sufficient air circulation
must be ensured:
eaners or sharp metal objects for cleaning the glass
Do not try to repair the appliance on your own. Always contact an authorized
technician. If the supply cord is damaged, it must be replaced by the
manufactur-
er, its service agent or similarly qualified persons in order to avoid a hazard.
Installation
InstallationInstallation
Installation
and the connection to the main power
may only be performed by an authorized specialist.
, the cabinet, veneers
, plastic coat-
adhesives etc. must be sufficient
heat-
must be installed so that heat can
Air inlet (D) and
air outlet (E) must
The appliance conforms to the heat insulation
class Y, i.e. only one side of the appliance may be
installed near higher kitchen furniture or walls.
The distance between the hob and an extractor
large as specified in the
instructions of the extractor hood!
Below the cutout must remain a minimum di
s-
tance (B). In this area are not allowed heat
-
sensitive objects (cabinet, drawer, etc.). Possibly
existing sidewalls or drawer boxes must be sawed
; sufficient air circulation
A
AA
A 600 – 750 mm
B
BB
B 50 mm
C
CC
C 20 mm
D
DD
D Air inlet
E
EE
E Air outlet