15
which is necessary remove the cover.
2. Unscrew the nut from the body of the push
button, while holding the stainless steel washer
and rubber gasket in place. Place one end of the
PVC tube on the spout on the body Press the other
end to A hole in the table top and a nut located
under the countertop.
3. Place the push button housing in the hole and
tighten the nut underneath countertop (enough
arm eort). Do not use the key to tighten nut.
4. Take the other end of the duct and tightly put
it on the spout of the air switch located on the
bottom of the disposer. Hand tighten the clamping
nut. The disposer installation is complete. Before
using the product, read all of the instructions.
operation and safety contained in paragraph 10 of
this manual. In conclusion, install the plug in the
sink in the Closed position. Fill the sink with water,
Remove the plug and check the connections on
the a water leakage.
10. ATTENTION! IMPORTANT INSTRUCTIONS
FOR SAFETY
• If the air switch does not work, remove the plug
power supply from the outlet and check the air
duct pneumatic switch and delivered to the outlet
electricity.
• This product is designed for grinding food
residues at home; the ingress of substances other
than food into the disposer may cause injury and /
or damage property. To reduce the risk of Do not
use a washer with an installed disposer not for
food purposes (for example, for bathing a child or
washing your head).
• Children should be supervised adults and should
not play with a disposer. To reduce the risk of injury
It is necessary to keep a watchful eye on children
use of the product.
• If the wedging in the disposer is eliminated,
turn o the appliance and disconnect it from the
electrical network. Use a wrench for self-removal
of jammed waste according to description in the
section “Elimination of jamming disposer “.
• Use tongs or pliers to remove foreign objects
from the product.
• To reduce the risk of injury from particles that are
thrown out by the disposer, it is prohibited to use
grinders withoutnoise shielding screen. Place the
plug in the drain hole.
Do not allow the following items to fall into the
disposer: shells, including oyster, caustic means for
cleaning pipes or similar chemical products, glass,
porcelain or plastic, large (hollow) bones, metal
objects (bottle caps, cans, or kitchen appliances),
hot fat or other hot liquids.
• Replace worn noise glossy screen / installation
gasket / protective reector if they are worn and
are no longer able to prevent waste or water.
• If the disposer is switched o, use a stopper to
prevent foreign objects in the grinding camera.
Make sure that the power of the disposer is
disabled.
• Before pressing the reset button, cleaning the jam
or removing foreign objects from the shredding
chamber, make sure that the food is turned o.
• Keep hands and ngers out of the reach of
disposer chamber.
FIRE RISK:
To minimize the possibility of Do not store near
re extinguishing articles such as rags, paper or
aerosol cans. Do not store or use gasoline or other
ammable vapor-gas mixtures and liquid near
the disposer. Do not allow the following camera
products: paints, solvents, household cleaning
agents and chemicals, automotive liquids, plastic
packaging.
USER’S MANUAL
1. Use air switch for starting disposer.
2. Slowly lower food waste into the chamber and
install the lter grid in a vertical position (so that
it ows through it water) to reduce noise and
possible throwing waste during grinding.
3. After the grinding is completed, turn o the
disposer and let the water run for at least 15 s to
ush the drain line.
SHOULD
• Grind food waste under pressure cold water not
less than 6 liters / min.
• Grind solids, such as small bones and fruit
residues, for cleaning chopping chambers.
• Grind citrus fruits, melons, vegetables and coee
beans.
• After the grinding is nished, let the water run out
at least 15 seconds to ush the drain pipeline.
• Unplug the product from the socket before
To Next Page
Loading...