46
Boschtools.com
Toll Free: 877-BOSCH-99
Item # Diameter
Usable
Length
Overall
Length Quantity
HC2000 5/32" 2" 4" 1
HC2001 5/32" 4" 6" 1
HC2001B5 5/32" 4" 6" 5
HC2001B25 5/32" 4" 6" 25
HC2010 3/16" 2" 4" 1
HC2010B5 3/16" 2" 4" 5
HC2010B25 3/16" 2" 4" 25
HC2011 3/16" 4" 6" 1
HC2011B5 3/16" 4" 6" 5
HC2011B25 3/16" 4" 6" 25
HC2012 3/16" 6" 8" 1
HC2012B5 3/16" 6" 8" 5
HC2012B25 3/16" 6" 8" 25
HC2013 3/16" 8" 10" 1
HC2013B5 3/16" 8" 10" 5
HC2013B25 3/16" 8" 10" 25
HC2014 3/16" 10" 12" 1
HC2014B5 3/16" 10" 12" 5
HC2014B25 3/16" 10" 12" 25
HC2015 3/16" 12" 14" 1
HC2015B5 3/16" 12" 14" 5
HC2015B25 3/16" 12" 14" 25
HC2020 .202" 2-3/4" 4-3/4" 1
HC2020B5 .202" 2-3/4" 4-3/4" 5
HC2020B25 .202" 2-3/4" 4-3/4" 25
HC2021 .202" 4-1/2" 6-1/2" 1
HC2021B5 .202" 4-1/2" 6-1/2" 5
HC2021B25 .202" 4-1/2" 6-1/2" 25
HC2022 .202" 6-1/2" 8-1/2" 1
HC2022B5 .202" 6-1/2" 8-1/2" 5
HC2022B25 .202" 6-1/2" 8-1/2" 25
HC2023 .202" 7-1/2" 9-1/2" 1
HC2023B5 .202" 7-1/2" 9-1/2" 5
HC2023B25 .202" 7-1/2" 9-1/2" 25
HC2031 7/32" 4" 6" 1
HC2031B5 7/32" 4" 6" 5
HC2031B25 7/32" 4" 6" 25
HC2032 7/32" 6" 8" 1
HC2032B5 7/32" 6" 8" 5
HC2032B25 7/32" 6" 8" 25
HC2034 7/32" 10" 12" 1
HC2034B5 7/32" 10" 12" 5
HC2034B25 7/32" 10" 12" 25
HC2040 1/4" 2" 4" 1
HC2040B5 1/4" 2" 4" 5
HC2040B25 1/4" 2" 4" 25
HC2041 1/4" 4" 6" 1
HC2041B5 1/4" 4" 6" 5
HC2041B25 1/4" 4" 6" 25
HC2042 1/4" 6" 8" 1
HC2042B5 1/4" 6" 8" 5
HC2042B25 1/4" 6" 8" 25
HC2043 1/4" 8" 10" 1
HC2045 1/4" 12" 14" 1
HC2051 5/16" 4" 6" 1
HC2051B5 5/16" 4" 6" 5
HC2051B25 5/16" 4" 6" 25
HC2054 5/16" 10" 12" 1
SDS-plus® S4® Tapcon® Hex Rotary Hammer Bits
For use with Tapcon® / Condrive systems. Hex drive on bit fits into driver sleeve.
SDS-plus® S4® Rotary Hammer Bits continued
Tapcon
®
is a registered trademark of Illinois Tool Works.
SDS-plus
®
is a registered trademark of Robert Bosch GmbH.
NOTE: Drill bits (or extension + drill bit) in excess of 8" should never exceed 600 RPM.
Item # Diameter
Usable
Length
Overall
Length Quantity
HC2301 5/32" 3" 6" 1
HC2301B25 5/32" 3" 6" 25
HC2302 5/32" 4" 7" 1
HC2302B25 5/32" 4" 7" 25
HC2310 3/16" 2" 5" 1
HC2310B25 3/16" 2" 5" 25
HC2311 3/16" 3" 6" 1
HC2311B25 3/16" 3" 6" 25
HC2312 3/16" 4" 7" 1
HC2312B25 3/16" 4" 7" 25
Item # Diameter
Usable
Length
Overall
Length Quantity
HC2061 3/8" 4" 6" 1
HC2061B5 3/8" 4" 6" 5
HC2061B25 3/8" 4" 6" 25
HC2064 3/8" 10" 12" 1
HC2064B5 3/8" 10" 12" 5
HC2064B25 3/8" 10" 12" 25
HC2067 3/8" 16" 18" 1
HC2068 3/8" 22" 24" 1
HC2071 7/16" 4" 6" 1
HC2074 7/16" 10" 12" 1
HC2081 1/2" 4" 6" 1
HC2081B5 1/2" 4" 6" 5
HC2081B25 1/2" 4" 6" 25
HC2084 1/2" 10" 12" 1
HC2084B5 1/2" 10" 12" 5
HC2084B25 1/2" 10" 12" 25
HC2087 1/2" 16" 18" 1
HC2088 1/2" 22" 24" 1
HC2091 9/16" 4" 6" 1
HC2094 9/16" 10" 12" 1
HC2097 9/16" 16" 18" 1
HC2098 9/16" 23" 28" 1
HC2099 9/16" 31" 36" 1
HC2102 5/8" 6" 8" 1
HC2102B5 5/8" 6" 8" 5
HC2102B25 5/8" 6" 8" 25
HC2104 5/8" 10" 12" 1
HC2107 5/8" 16" 18" 1
HC2108 5/8" 22" 24" 1
HC2112 11/16" 6" 8" 1
HC2122 3/4" 6" 8" 1
HC2124 3/4" 10" 12" 1
HC2127 3/4" 16" 18" 1
HC2128 3/4" 22" 24" 1
HC2137 27/32" 6" 8" 1
HC2142 7/8" 6" 8" 1
HC2144 7/8" 10" 12" 1
HC2147 7/8" 16" 18" 1
HC2163 1" 8" 10" 1
HC2167 1" 16" 18" 1
SDS-plus® Rotary Hammer Bits
15% more life time in concrete (compared to the last version of S4)
• Optimized brazing and hardening process for top resistance
in reinforced concrete
• Optimized flute design to reduce stress and make the
bit run cooler
• 4-flute design for fast dust removal
• Centric tip for optimal hole geometry
Masonry/Concrete Drilling
To Next Page
Loading...
