20 | English
1 609 92A 16W | (12.2.15) Bosch Power Tools
Technical Data
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section “Af-
ter-sales Service and Application Service”.
Protection Guard for Grinding
Place the protection guard 12 on-
to the spindle collar as shown in
the illustration. The triangle marks
on the protection guard must cor-
respond with the respective
marks on the gear case.
Press the protection guard 12 on-
to the spindle collar until the
shoulder of the protection guard
is seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Adjust the position of the protection guard 12 to the require-
ments of the work process. For this, press the release lever 1
upward and turn the protection guard 12 to the required po-
sition.
Adjust the protection guard 12 in such a manner that
sparking is prevented in the direction of the operator.
The protection guard 12 may be turned only upon actu-
ation of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
Note: The encoding keys on the protection guard 12 ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 14.
Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 14 is mounted in the same
manner as the protection guard for grinding 12.
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard 21 is
mounted in the same manner as the protection guard for
grinding 12.
Extraction Hood for Sanding
The extraction hood 7 can be used for low-dust sanding of
paint, varnish and plastics in conjunction with the carbide
grinding head 9 or the rubber sanding plate 17 with a sanding
sheet 18. The extraction hood 7 is not suitable for working
metals.
Angle Grinder GWS ... 15-125 CIH 15-125 CIEH 15-125 CITH 15-125 CISTH 15-150 CIH
Article number
3 601 ... H30 2..
H30 C..
H30 3..
H30 D..
H30 4..
H30 E..
H30 7..
H30 G..
H30 5..
H30 F..
Rated power input W 1500 1500 1500 1500 1500
Output power
W 860 860 860 860 860
Rated speed
min
-1
11000 11000 9300 7500 9300
Speed control adjustment
min
-1
– 2800–11000 2800–9300 ––
Grinding disc diameter, max.
mm 125 125 125 125 150
Thread of grinder spindle
M 14 M 14 M 14 M 14 M 14
Thread length (max.) of grinder
spindle
mm 22 22 22 22 22
Kickback stop
Restarting Protection
Reduced starting current
Constant electronic control
Speed preselection
– ––
Weight according to
EPTA-Procedure 01/2003
– with vibration-damping
auxiliary handle
– with standard-auxiliary handle
kg
kg
2.5
2.4
2.5
2.4
2.5
2.4
2.5
2.4
2.6
2.5
Protection class /II /II /II /II /II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
OBJ_BUCH-165-007.book Page 20 Thursday, February 12, 2015 10:55 AM
To Next Page
Loading...
