Bosch D7412GV2 - Page 6

D9412GV2/D7412GV2 | Operation and Installation Guide | Contents
6 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
Figures
Figure 1: System Configuration..............................9
Figure 2: Enclosure Mounting ..............................15
Figure 3: Ground Fault Detection.........................16
Figure 4: Ground Fault Detect (S4)......................17
Figure 5: Area 5 Silent Alarm Relay in RPS.........17
Figure 6: Reset Pin...............................................18
Figure 7: D9412GV2 Service Walk Test Flow
Chart .....................................................21
Figure 8: D7412GV2 Service Walk Test Flow
Chart .....................................................22
Figure 9: Non-Power-Limited Wiring ....................25
Figure 10: Charging and Battery LEDs ..................26
Figure 11: RJ31X Wiring ........................................30
Figure 12: Phone Connector, Phone LED, and
Operation Monitor LED Locations.........30
Figure 13: D928 Dual Phone Line Switcher...........33
Figure 14: On-board Point Sensor Loop Wiring.....35
Figure 15: Rothenbuhler 5110/4001-42 High
Security Bell Wiring Configuration ........37
Figure 16: Wiring the Rothenbuhler 5110/4001-42
High Security Bell to the D9412GV2
or D7412GV2 Control Panel .................38
Figure 17: Connecting the D8125 POPEX to the
D9412GV2 Control Panel .....................41
Figure 18: Connecting the D8125 POPEX to the
D7412GV2 Control Panel .....................42
Figure 19: Program Record Sheet .........................45
Figure 20: D8128D OctoPOPIT Layout..................46
Figure 21: Connecting D8128D OctoPOPITs to
the D9412GV2 ......................................49
Figure 22: Connecting D8128D OctoPOPITs to
the D7412GV2 ......................................50
Figure 23: Wiring Multiple D8128Ds Using
Molex
®
Connectors ...............................51
Figure 24: D8128D OctoPOPIT Sensor Loops ......52
Figure 25: D8129 Connections to the D9412GV2 .53
Figure 26: D8129 Connections to the D7412GV2 .54
Figure 27: D811 Module Wiring to the
D9412GV2 ............................................56
Figure 28: D811 Module Wiring to the
D7412GV2 ............................................57
Figure 29: Power at Keypads.................................60
Figure 30: Keyswitch Wiring...................................61
Figure 31: D9133 Jumper Setting for Address 80..64
Figure 32: DX4010i DIP Switch Settings................64
Figure 33: DX4020 DIP Switch Settings ................65
Figure 34: Reset Pin...............................................66
Figure 35: Programmer and Accessory
Connections.......................................... 66
Figure 36: D9412GV2 Faceplate........................... 67
Figure 37: D7412GV2 Faceplate........................... 68
Figure 38: D9412GV2, Power Supply Side ........... 69
Figure 39: D9412GV2, Input Points and
Peripheral Devices ............................... 70
Figure 40: D9412GV2, SDI Devices...................... 71
Figure 41: D7412GV2, Power Supply Side ........... 72
Figure 42: D7412GV2, Input Points and
Peripheral Devices ............................... 73
Figure 43: D7412GV2, SDI Devices...................... 74
Tables
Table 1: Related Documentation.......................... 7
Table 2: GV2 Series Control Panel Differences... 9
Table 3: Compatible Accessories....................... 10
Table 4: Software Version Compatibility of
D6500 MPU and Line Cards ................ 13
Table 5: Compatible Keypads and Command
Centers ................................................. 13
Table 6: Ground Fault Impedance
Specifications ....................................... 17
Table 7: Battery Discharge and Recharge
Schedule............................................... 27
Table 8: Charging Status and Low Battery
LEDs..................................................... 27
Table 9: Phone Cord Lengths............................. 33
Table 10: Point Parameters.................................. 35
Table 11: POPEX Modules................................... 39
Table 12: Extra Point Events................................ 39
Table 13: Off-Board Point Errors.......................... 40
Table 14: Data Expansion Loop Wire
Specifications ....................................... 43
Table 15: D8128D OctoPOPIT Switch Settings
for D9412GV2 and D7412GV2............. 47
Table 16: Switch 5 Settings for Line Termination. 47
Table 17: Terminal Strip Connections .................. 48
Table 18: D8129 OctoRelay Switch Settings ....... 54
Table 19: Number of D8128Ds Used with D8129s
.............................................................. 55
Table 20: Keypad Address Settings ..................... 58
Table 21: Keypad Connections ............................ 59
Table 22: SDI Device Connections ...................... 62
Table 23: Printer Address Switch Settings ........... 62
Table 24: Address Switch Settings for Access
Control Module ..................................... 63
Table 25: Zonex 1 Point Address Chart ............... 75
Table 26: Zonex 2 Point Address Chart ............... 76
Table 27: Specifications ....................................... 77