Bosch AddressiFire DS9400M User Manual (English)

To Next Page

Fire Alarm Systems | DS9400M AddressiFire Fire Alarm Control Panel

The DS9400M AddressiFire 255 is a microprocessor-based

Fire Alarm Control Panel. This four conventional point panel

can expand to 255 input points. It supports up to twenty

two-wire detectors per on-board conventional point, or any

number of four-wire detectors (depending on available

power). Two Notification Appliance Circuits (NACs) provide

up to 4 A of 24 V power to operate horns, strobes, bells and

other notification appliances. The DS9431 Multiplex

Expansion Module (pre-installed) enhances the DS9400M’s

conventional system features by adding addressable point

capability, increasing the number of relay outputs and

allowing for more system users.

Functions

Easy user interface

Nine labeled function keys allow the user to easily silence

bells, sirens, reset smoke detectors, or view history events.

Menu driven keypad programming allows for customizing of

the control panel.

Keypad programmable

The system is completely keypad programmable, thus

eliminating the need for an expensive hand-held

programmer.

Initiating circuits

All on-board conventional input points will work with two-

wire or four-wire smoke detectors. Twenty detectors (two-

wire) maximum per zone.

Multiplex expansion technology

The DS9431 Multiplex Expansion Module (pre-installed)

enhances the DS9400M conventional system features by

expanding the base system to 255 total points, increasing

the number of relay outputs to 58 and adding an additional

400 events to the history buffer for a total of 500 non-

volatile events. The DS9431 also allows for up to 100

system users on the DS9400M.

Built-In and remote alpha keypad support

The keypad built in to the control panel and the DS9447

remote LCD keypad are alphanumeric keypads that provide

a two-line, 16‑character (per line) LCD display. Text is freely

programmable for zone descriptions. Up to four DS9447

remote LCD keypads are allowed per system.

Personal ID Numbers (PINs)

The system supports up to 100 Personal ID Numbers (PINs),

which are four digits in length. The PINs may contain any

combination of digits. PINs may be programmed with four

different levels of authority. These PINs may be restricted

to silencing, resetting, disabling, and/or programming the

system.

DS9400M AddressiFire Fire Alarm Control

Panel

▶

Digital Fire Alarm Control Panel

▶

Provided with four conventional on-board inputs,

expandable to eight

▶

Up to 247 Addressable Multiplex Points

▶

Supports two-wire and four-wire conventional type

detectors

▶

Two NACs

▶

Two On-Board Auxiliary Relays

▶

Internal 24 V, 4 A power supply

▶

Supports four remote LCD Keypads

▶

On-board programming via front panel

▶

Expandable to 255 points

www.boschsecurity.com

Need help?

Do you have a question about the Bosch AddressiFire DS9400M and is the answer not in the manual?

Bosch AddressiFire DS9400M Specifications

Enclosure Design

enclosure height	53 cm (20.8 in)
enclosure width	38.1 cm (15.0 in)
enclosure depth	11.0 cm (4.3 in)
enclosure material	1.2 mm cold-rolled steel

Environmental Considerations

operating temperature range	0°C to +49°C (+32°F to +120°F)

Inputs and Outputs

supervisory EOL resistor	2.21 kΩ
maximum keypads	four
on-board relays	Two Form 'C' relays rated at 5 A, 28 VDC
NAC outputs	Two 24 V outputs, 2.5 A capacity each (limited by 4.0 A overall capacity)

Power Requirements

auxiliary power	20 VDC to 30 VDC unfiltered, 1 A
initiating circuit power	20.4 VDC to 28.2 VDC filtered, 1 A
input power	120 VAC, 1.5 A
NAC power	20 VDC to 30 VDC unfiltered, 4 A
open bus power	12 V±5%, 500 mA
standby batteries	Two 12 V (in series), 7 Ah to 40 Ah
standby current (detector)	3 mA maximum total per point