English | 9
u Disconnect the plug from the power source and/or re-
move the battery pack, if detachable, from the power
tool before making any adjustments, changing ac-
cessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
u Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
u Maintain power tools and accessories. Check for mis-
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
u Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
u Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
u Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
u Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety instructions for metal shears
u This power tool is not suitable for bench-mounted use.
It must not be clamped into a vice or fastened to a work-
bench, for example.
u Only carry out work with a fitted chip guard. Make
sure that the chip guard is not damaged or bent out of
shape. Working without a chip guard or with a damaged
chip guard poses a risk of injury. If your chip guard is
damaged, have it replaced immediately by an authorised
Bosch after-sales agent.
u Wear protective gloves during work and pay particu-
lar attention to the cord. Make sure that cut sheet
parts are not bent towards your body or the cord.
Sharp burrs develop on the cut sheets; these can cause
injury or damage the cord. When necessary and while
wearing gloves, press bending sheet parts away from
your body and/or from the cord.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for cutting sheet metals without
incurring any loss from chipping. It is suitable for straight
and curved cuts.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
On/off switch
(2)
Chip deflector
(3)
Handle (insulated gripping surface)
(4)
Fastening screw for upper cutter
(5)
Upper cutter
(6)
Bottom cutter
(7)
Set screw for bottom cutter
(8)
Fastening screw for bottom cutter
(9)
Hex key
A)
A)
Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Sheet metal shears GSC 75-16
Article number
3601E005..
Rated power input W 750
Power output W 400
No-load stroke rate n
0
min
−1
5200
Stroke speed under load min
−1
4000
Max. steel sheet cutting
capacity
A)
mm 1.6
Smallest curve radius mm 35
Weight according to
EPTA-Procedure 01:2014
kg 1.7
Bosch Power Tools 1 609 92A 50F | (27.06.2019)
To Next Page
Loading...
