English–3
2 609 932 513 • 24.4.06
Technical Data
Assembly
Changing the Tool (see figure A)
Pull off the screwing-depth stop 4 toward the front. Pull
out the screwdriver bit 1. If required, the universal bit
holder 9 can also be pulled off and replaced.
After changing the tool, reattach the screwing-depth
stop 4.
Operation
Starting Operation
f Observe correct mains voltage! The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Power tools marked with 230 V can also be
operated with 220 V.
Reversing the Rotational Direction
The rotational direction switch 8 is used to reverse the
rotational direction of the machine. However, this is not
possible with the On/Off switch 7 actuated.
Right rotation: Push the rotational direction switch 8
left to the stop (for screwing in screws).
Left rotation: Push the rotational direction switch 8
right to the stop (for unscrewing screws).
Switching On and Off
To start the machine, press the On/Off switch 7 and
keep it depressed.
To lock the pressed On/Off switch 7, press the lock-
on button 6.
To switch off the machine, release the On/Off switch
7 or when it is locked with the lock-on button 6, briefly
press the On/Off switch 7 and then release it.
Adjusting the Speed
The speed of the switched on power tool can be varia-
bly adjusted, depending on how far the On/Off switch
7 is pressed.
Light pressure on the On/Off switch 7 results in a low
rotational speed. Further pressure on the switch results
in an increase in speed.
Adjusting the Screw-in Depth (see figure B)
With the adjustment sleeve 3, the screw-in depth of the
screw head into the workpiece can be preset in 8 lock-
ing steps per full turn. Each step corresponds with a
0.25 mm change of the screw-in depth.
Turning the adjustment sleeve 3 in clockwise direction
results in a greater screw-in depth; turning in anticlock-
wise direction reduces the screw-in depth.
The required setting is best determined by testing.
Operating Instructions
f Apply the power tool to the screw only when
it is switched off.
Guide the screw toward the screwdriving bit 1. The
screw is held in place by the magnet pull of the univer-
sal bit holder 9. Firmly push the tip of the screw into the
material to be screwed until the screwing-depth stop 4
faces against the workpiece.
Switch the machine on. The screw is screwed into the
material until the adjusted screw-in depth is reached.
The drive is disengaged and the tool holder no longer
rotates. Check the screw-in depth and readjust, if
required.
For unscrewing screws, set the rotational direction
switch 8 to left rotation and pull off the screwing-depth
stop 4 toward the front without turning the adjustment
sleeve.
Working with the screwing-depth stop 4 is also possi-
ble when adapting the screw-in depth.
Screwdriver GSR 6-25 TE
PROFESSIONAL
GSR 6-45 TE
PROFESSIONAL
Article number 3 601 D41 3.. 3 601 D40 3..
Rated power input W 701 701
Output power W 327 327
No-load speed rpm 0–2500 0–4500
Rated speed rpm 0–1700 0–3000
Tool holder ¼" hexagon socket ¼" hexagon socket
Max. screw dia. mm 6 6
Weight according to EPTA-Procedure 01/2003 kg 1.5 1.4
Protection class /II /II
The values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries, these val-
ues can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
OBJ_BUCH-137-001.book Page 3 Monday, April 24, 2006 9:59 AM
To Next Page
Loading...
