10 | English
1 609 92A 196 | (12.8.15) Bosch Power Tools
Selecting Grinding Discs
Dust/Chip Extraction
Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dust can
easily ignite.
Operation
Starting Operation
Inserting the battery
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
Insert the charged battery 4 into the handle until it can be felt
to engage and faces flush against the handle.
Switching On and Off
To start the power tool, push the On/Off switch 3 forwards.
To lock the On/Off switch 3, press the On/Off switch 3 down
at the front until it latches.
To switch off the power tool, release the On/Off switch 3 or,
if it is locked, briefly push down the back of the On/Off switch
3 and then release it.
To save energy, only switch the power tool on when using it.
Check grinding tools before using. The grinding tool
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grind-
ing tools. Damaged grinding tools can burst and cause in-
juries.
Temperature Control/Overload Protection Indicator
The red LED indicator 6 will help you in protecting the battery
against overheating and the motor against overloading.
When the LED indicator 6 continuously lights up red, the
temperature of the battery is too high and the machine
switches off automatically.
– Switch the power tool off.
– Allow the battery to cool down before continuing to work.
The LED indicator 6 flashes red, the power tool is blocked
and switches off automatically.
– Remove the power tool from the workpiece.
The power tool will continue to work as soon as the block-
age is rectified.
Working Advice
Exercise caution when cutting slots in structural walls;
see Section “Information on Structures”.
When cutting lightweight materials, take into account
the statutory provisions and recommendations of the
material manufacturer.
Clamp the workpiece if it does not remain stationary
due to its own weight.
Do not strain the machine so heavily that it comes to a
standstill.
After heavily straining the power tool, continue to run
it at no-load for several minutes to cool down the acces-
sory.
Do not touch grinding and cutting discs before they
have cooled down. The discs can become very hot while
working.
Do not use the power tool with a cut-off stand.
When the power tool is electrostatically charged, the built-in
electronic control switches it off. To restart the power tool,
press the On/Off switch 3 again.
Rough Grinding
Never use a cutting disc for roughing.
The best roughing results are achieved when setting the ma-
chine at an angle of 30° to 40°. Move the machine back and
forth with moderate pressure. In this manner, the workpiece
will not become too hot, does not discolour and no grooves
are formed.
Cutting Metal
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 10.
When cutting, work with moderate feed, adapted to the mate-
rial being cut. Do not exert pressure onto the cutting disc, tilt
or oscillate the machine.
Do not reduce the speed of running down cutting discs by ap-
plying sideward pressure.
max.
[mm]
[mm]
D b d [min
-1
] [m/s]
76 7 10 19.500 80
Grinding discs Material
Carbide Multi Wheel PVC, wood,
composites,
perspex
Expert for Metal Aluminium,
copper
Best for Ceramic Tile, concrete,
brick
To Next Page
Loading...
