Bosch NIT8060UC - Overview of the Home Connect Settings; Changing Settings Via the Home Connect App; Software Update

en-us HomeConnect™
20
7.2 Overview of the HomeConnect™ settings
You can adjust the settings and network settings for HomeConnect™ in the basic settings for your appliance.
Setting Selection or display Description and additional information
⁠ – Not connected/disconnect network
– Connect automatically
– Connect manually
– Connected
Log the appliance on in the home network (Wi-Fi) or dis-
connect from the network.
⁠ – Not connected
– Connect
Connecting to the app
The setting is only displayed if the appliance is connected
to the home network.
⁠ – Wireless module switched off
– Wireless module switched on
Connection to the (Wi-Fi)
If (Wi-Fi) has been activated, you can use the HomeCon-
nect™ functions.
In networked standby mode, your appliance requires a
maximum of 2W.
The setting is only displayed if the appliance has been pre-
viously connected to a network.
⁠ – Switched off
– Switched on
Set using the app
If the setting is switched off, only the cooktop's operating
statuses will be displayed in the HomeConnect™ app.
⁠ – Update available and ready for instal-
lation
– Start installation starten
Software update
The setting is only displayed if a software update is avail-
able.
⁠ – Not authorized
– Authorized
Controlling remote access by Customer Support
The setting is only displayed if after-sales service is at-
tempting to connect to the appliance. You can end this at
any time after granting access.
⁠ – Not connected to the home network
(Wi-Fi)
– Signal strength 1 (poor)
– Signal strength 2 (moderate)
– Signal strength 3 (good)
Display Wi-Fi signal strength
The setting is only displayed if there is a connection to the
home network (Wi-Fi).
⁠ – Not connected
– Connected
Connection to HomeConnect™ server
The setting is only displayed if there is a connection to the
home network (Wi-Fi).
7.3 Changing settings via the HomeCon-
nect™ app
You can use the HomeConnect™ app to change the set-
tings for the cooking zones and send them to the cooktop.
Requirements
¡ The appliance is connected to the home network and to
the HomeConnect™ app.
¡ In order to set the hob via the app, the basic setting
must be switched on.
¡ The hob is switched on.
1. Select the setting in the HomeConnect™ app and send
it to the cooktop.
Follow the instructions in the HomeConnect™ app.
2. If the setting was previously , two steps are required:
‒ If confirm flashes, touch confirm.
‒ If the cooking zone display alternately flashes the old
and new value, select the cooking zone.
3. If the setting was not previously , the old and new
value alternately flash directly on the cooking zone dis-
play.
‒ To accept the setting for the cooking zone, select the
cooking zone.
4. To discard the setting, touch any other button on the
cooktop.
7.4 Software update
Your appliance's software can be updated using the soft-
ware update function, e.g. for the purposes of optimiza-
tion, troubleshooting or security updates.
To do this, you must be a registered HomeCon-
nect™user, have installed the app on your mobile device
and be connected to the HomeConnect™server.
As soon as a software update is available, you will be in-
formed via the HomeConnect™app and will be able to
start the software update via the app. Once the update
has been successfully downloaded, you can start installing
it via the HomeConnect™app if you are in your local area
network. The HomeConnect™app will inform you once
installation is successful.
Notes
¡ You can continue to use your appliance as normal while
updates are downloading. Depending on your personal
settings in the app, software updates can also be set to
download automatically.
¡ We recommend that you install security updates as
soon as possible.