Bosch Professional GOF 130 - Fitting; Inserting the Router Bit; Dust Chip Extraction

English | 9
(16)
Clamping lever for locking the routing depth
(17)
Unlocking lever for guide bushing
(18)
Router bit
a)
(19)
On/off switch
(20)
Speed preselection thumbwheel
(21)
Cap nut with collet
(22)
Open-ended spanner (19mm)
(23)
Extraction hose (dia. 35 mm)
a)
(24)
Dust extraction adapter
(25)
Knurled screw for dust extraction adapter (2x)
(26)
Guide rod for parallel guide (2x)
(27)
Parallel guide
(28)
Centring pin
a)
(29)
Wing bolt for centring pin
a)
(30)
Curve guide
a)
(31)
Router compass/guide rail adapter
a)
(32)
Handle for router compass
a)
(33)
Wing bolt for router compass coarse adjustment
(2x)
a)
(34)
Wing bolt for router compass fine adjustment (1x)
a)
(35)
Knob for router compass fine adjustment
a)
(36)
Centring screw
a)
(37)
Guide rail
a)
(38)
Spacer plate (part of the router compass set)
(39)
Guide bushing
a)
Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Router GOF 130
Article number
3601FB70..
Rated power input W 1300
No-load speed min
−1
11000–28000
Speed preselection ●
Constant electronic control ●
Connection for dust extraction ●
Compatible collets mm
inches
6/8
¼
Router cage stroke mm 55
Weight according to
EPTA-Procedure01:2014
kg 3.5
Protection class
/II
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Fitting
u Pull the plug out of the socket before carrying out any
work on the power tool.
Inserting the router bit (seefigureA)
u Wearing protective gloves while fitting and changing
router bits is recommended.
Router bits are available in a wide variety of designs and
qualities depending on the intended application.
Router bits made of high-performance high-speed steel
(HSS) are suited to machining soft materials such as soft-
wood and plastic.
Router bits with carbide tips are especially suitable for
hard and abrasive materials such as hardwood and alu-
minium.
Original router bits from the extensive range of Bosch ac-
cessories are available from your specialist dealer.
Only use undamaged and clean router bits.
– Pull the chip protection(5) downwards.
– Press and hold the spindle lock button(3). If necessary,
turn the motor spindle manually until it is locked in place.
– Loosen the cap nut(21) with the open-ended
spanner(22) (width across flats of 19mm) by turning it
in direction.
– Slide the router bit into the collet. The shank of the router
bit must be pushed at least 20mm into the collet.
– Tighten the cap nut(21) with the open-ended
spanner(22) (width across flats of 19mm) by turning it
in direction. Release the spindle lock button(3).
– Pull the chip protection(5) upwards.
u Do not insert a router bit with a diameter larger
than50mm when the guide bushing is not mounted.
These router bits will not fit through the base plate.
u Do not, under any circumstances, tighten the collet
with the tightening nut until a router bit has been fit-
ted. The collet may otherwise become damaged.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Bosch Power Tools 1 609 92A 5MU | (31.03.2021)