To Next PageTo Next Page
Need help?Do you have a question about the Bosch SHU9906 and is the answer not in the manual?
Explains the warning symbol used in instructions and on this page.
Lists potential hazards associated with dishwashers, such as electric shock.
Provides warnings about electric shock and personal injury during operation or repair.
Warns about property damage from improper water connections, especially overtightening.
Notes that no PC boards are handled in repairs, as they are in plastic housings.
States that no CFCs or refrigerants are used in Bosch dishwashers.
Mentions no emissions, but occasional smells may come from improperly connected drains.
Confirms that no carbon monoxide is emitted by dishwashers.
States there are no specific government compliance issues mentioned.
Lists UL certification and Energy Star certification for energy savings.
Details electrical, water pressure, motor, and pump specifications.
Explains current and older model number structures for identification.
Shows the location of the serial number label on the inner door edge.
Indicates that the wiring and circuit diagram is folded in the dishwasher base.
Outlines various limited warranty periods for parts and labor.
Refers to attached installation instructions for proper dishwasher placement.
Refers to attached installation instructions for electrical connections.
Refers to attached installation instructions for water and drain connections.
Refers to attached installation instructions for removing packaging.
Lists steps including leveling, handle installation, door reversal, and testing.
Explains how the dishwasher uses pumps, heaters, sensors, and drying cycles.
Details various components like circulation pump, heater, NTC, and sensors.
Describes accessing the water valve by removing the toe kick.
Shows different water valve part numbers and upgrade information.
Details removing the outer door to access the circulation pump.
Describes removing toe kick and side panels for circulation pump access.
Explains raising the tank to gain access to the circulation pump.
Provides steps to remove the circulation pump motor from its housing.
Details the process of reassembling the circulation pump impeller and housing.
Explains how to remove control modules from fascia panels by bending tabs.
Details disassembly procedures for specific SHY/SHU/SHV control modules.
Describes removing display modules mounted on fascia panels for SHY56A/66C.
Details Apexx control module removal, which is mounted on the base.
Explains removing side panels to gain access to Apexx control modules.
Details raising the tank to gain access to Apexx control modules.
Shows locating, disconnecting, and sliding out Apexx control modules.
Describes removing the Apexx display module from fascia panels.
Explains accessing heaters and NTC by removing the outer door.
Describes removing toe kick and side panels for heater/NTC access.
Details separating the base from the tank to access heaters/NTCs.
Explains separating the base from the tank to access heaters/NTCs.
Describes removing and installing the heater assembly.
Describes removing and installing the NTC from the heater assembly.
Details removing and installing the drain pump, accessible via toe kick.
Explains removing and installing dispensers, with caution for sharp edges.
Discusses condensation tubes and vented vs. unvented dispensers.
Details disassembling door latches for integrated models.
Describes removing and installing door latches and microswitches.
Explains accessing the aqua sensor from the left side of the dishwasher.
Describes accessing the water fill assembly from the left side.
Lists models and button sequences to enter diagnostic test programs.
Lists error codes for test programs and customer error codes.
Guides on using test programs to measure heater and NTC resistances.
Provides a table of problems, causes, and suggested actions for basic issues.
Lists common issues related to specific dishwasher parts like valves and pumps.
Troubleshoots module display showing "1" due to unidentified heating problems.
Provides a flowchart for diagnosing heater circuit failures.
Outlines troubleshooting steps for water leaking past dishwasher doors.
Details checking the PTC pump motor starter for circulation pumps.
Provides resistance measurements for PTC pump motor starters.
Addresses nuisance tripping of thermal protectors on pumps with water switches.
Identifies new and original pumps and motor starters for water switch pumps.
Guides on loosening stuck impellers and replacing them.
Details replacing impellers due to debris or lack of use.
Shows impeller ceramic ring color codes to identify upgraded vs. old styles.
Lists part number changes for circulation pumps due to "softer bearing" upgrade.
Lists part number changes for circulation pumps in UC/14 models.
Details changes in part numbers for circulation pump assemblies and motors.
Discusses issues with heater relay soldering on control module PC boards.
Explains using a front cover to replace broken buttons on control modules.
Details replacing older control modules with #481055 and related pushbutton pads.
Shows pushbutton pads for older models and instructions to turn off the end-of-cycle tone.
Compares old and new pushbutton pads for SHV models.
Discusses using alternative heater assemblies for older UC/06 models.
Explains heater assemblies with motor-operated water switches for flow control.
Lists part numbers for water switch heater assemblies.
Describes sump part improvements made to aid draining and prevent jamming.
Provides instructions for replacing dispenser doors that are damaged or pulled off.
Details top-load dispensers and how to adjust rinse-aid dosage.
Explains top-load dispenser operation and absence of reed switches.
Guides on realigning door latches that cause doors not to close properly.
Addresses miswired door latches causing display issues and potential module damage.
Discusses larger terminal boxes with covers included since September 2003.
Shows wiring and resistance measurements for SHU43C/53A control modules.
Provides wiring and resistance measurements for SHX/SHV control modules.
Shows wiring and resistance measurements for SHU66C/SHI66A modules.
Details wiring and resistance measurements for SHX/SHV/SHY modules.
Provides wiring and resistance measurements for SHV/SHX/SHY modules.
Shows wiring and resistance measurements for SHU/SHI modules.
Details wiring and resistance measurements for SHU995X/SHV68 modules.
Provides wiring and resistance measurements for SHU/SHV modules.
Shows wiring and resistance measurements for SHU33/432x modules.
Details wiring and resistance measurements for SHU303x/313x modules.
Shows circulation pump resistance measurements for various models.
Provides circulation pump resistance measurements for SHU995x/SHV68.
Displays the wiring diagram for SHU 30 dishwasher models.
Shows the wiring diagram for SHU 303X/313X dishwasher models.
Displays the wiring diagram for SHU 40 dishwasher models.
Shows wiring diagrams for SHU 43C and SHU 53A dishwasher models.
Displays wiring diagrams for SHU 43E, SHU 53E, and SHU 66E models.
Shows wiring diagrams for SHU 33 and SHU 4322/4326 models.
Displays wiring diagrams for SHI 43/68 and SHU 43/53/68 models.
Shows wiring diagrams for SHI/SHU 43 models.
Displays wiring diagram for SHU 53 models.
Shows wiring diagrams for SHU 88/99 and SHV 43/48 models.
Displays wiring diagram for SHU 995X models.
Shows wiring diagram for SHV 68 models.
Displays wiring diagrams for SHU 66C and SHI 66A models.
Shows wiring diagrams for SHX and SHV models.
Displays wiring diagrams for SHY and SHV models.
Shows wiring diagrams for SHY, SHV, and SHX models.
Explains the warning symbol used in instructions and on this page.
Lists potential hazards associated with dishwashers, such as electric shock.
Provides warnings about electric shock and personal injury during operation or repair.
Warns about property damage from improper water connections, especially overtightening.
Notes that no PC boards are handled in repairs, as they are in plastic housings.
States that no CFCs or refrigerants are used in Bosch dishwashers.
Mentions no emissions, but occasional smells may come from improperly connected drains.
Confirms that no carbon monoxide is emitted by dishwashers.
States there are no specific government compliance issues mentioned.
Lists UL certification and Energy Star certification for energy savings.
Details electrical, water pressure, motor, and pump specifications.
Explains current and older model number structures for identification.
Shows the location of the serial number label on the inner door edge.
Indicates that the wiring and circuit diagram is folded in the dishwasher base.
Outlines various limited warranty periods for parts and labor.
Refers to attached installation instructions for proper dishwasher placement.
Refers to attached installation instructions for electrical connections.
Refers to attached installation instructions for water and drain connections.
Refers to attached installation instructions for removing packaging.
Lists steps including leveling, handle installation, door reversal, and testing.
Explains how the dishwasher uses pumps, heaters, sensors, and drying cycles.
Details various components like circulation pump, heater, NTC, and sensors.
Describes accessing the water valve by removing the toe kick.
Shows different water valve part numbers and upgrade information.
Details removing the outer door to access the circulation pump.
Describes removing toe kick and side panels for circulation pump access.
Explains raising the tank to gain access to the circulation pump.
Provides steps to remove the circulation pump motor from its housing.
Details the process of reassembling the circulation pump impeller and housing.
Explains how to remove control modules from fascia panels by bending tabs.
Details disassembly procedures for specific SHY/SHU/SHV control modules.
Describes removing display modules mounted on fascia panels for SHY56A/66C.
Details Apexx control module removal, which is mounted on the base.
Explains removing side panels to gain access to Apexx control modules.
Details raising the tank to gain access to Apexx control modules.
Shows locating, disconnecting, and sliding out Apexx control modules.
Describes removing the Apexx display module from fascia panels.
Explains accessing heaters and NTC by removing the outer door.
Describes removing toe kick and side panels for heater/NTC access.
Details separating the base from the tank to access heaters/NTCs.
Explains separating the base from the tank to access heaters/NTCs.
Describes removing and installing the heater assembly.
Describes removing and installing the NTC from the heater assembly.
Details removing and installing the drain pump, accessible via toe kick.
Explains removing and installing dispensers, with caution for sharp edges.
Discusses condensation tubes and vented vs. unvented dispensers.
Details disassembling door latches for integrated models.
Describes removing and installing door latches and microswitches.
Explains accessing the aqua sensor from the left side of the dishwasher.
Describes accessing the water fill assembly from the left side.
Lists models and button sequences to enter diagnostic test programs.
Lists error codes for test programs and customer error codes.
Guides on using test programs to measure heater and NTC resistances.
Provides a table of problems, causes, and suggested actions for basic issues.
Lists common issues related to specific dishwasher parts like valves and pumps.
Troubleshoots module display showing "1" due to unidentified heating problems.
Provides a flowchart for diagnosing heater circuit failures.
Outlines troubleshooting steps for water leaking past dishwasher doors.
Details checking the PTC pump motor starter for circulation pumps.
Provides resistance measurements for PTC pump motor starters.
Addresses nuisance tripping of thermal protectors on pumps with water switches.
Identifies new and original pumps and motor starters for water switch pumps.
Guides on loosening stuck impellers and replacing them.
Details replacing impellers due to debris or lack of use.
Shows impeller ceramic ring color codes to identify upgraded vs. old styles.
Lists part number changes for circulation pumps due to "softer bearing" upgrade.
Lists part number changes for circulation pumps in UC/14 models.
Details changes in part numbers for circulation pump assemblies and motors.
Discusses issues with heater relay soldering on control module PC boards.
Explains using a front cover to replace broken buttons on control modules.
Details replacing older control modules with #481055 and related pushbutton pads.
Shows pushbutton pads for older models and instructions to turn off the end-of-cycle tone.
Compares old and new pushbutton pads for SHV models.
Discusses using alternative heater assemblies for older UC/06 models.
Explains heater assemblies with motor-operated water switches for flow control.
Lists part numbers for water switch heater assemblies.
Describes sump part improvements made to aid draining and prevent jamming.
Provides instructions for replacing dispenser doors that are damaged or pulled off.
Details top-load dispensers and how to adjust rinse-aid dosage.
Explains top-load dispenser operation and absence of reed switches.
Guides on realigning door latches that cause doors not to close properly.
Addresses miswired door latches causing display issues and potential module damage.
Discusses larger terminal boxes with covers included since September 2003.
Shows wiring and resistance measurements for SHU43C/53A control modules.
Provides wiring and resistance measurements for SHX/SHV control modules.
Shows wiring and resistance measurements for SHU66C/SHI66A modules.
Details wiring and resistance measurements for SHX/SHV/SHY modules.
Provides wiring and resistance measurements for SHV/SHX/SHY modules.
Shows wiring and resistance measurements for SHU/SHI modules.
Details wiring and resistance measurements for SHU995X/SHV68 modules.
Provides wiring and resistance measurements for SHU/SHV modules.
Shows wiring and resistance measurements for SHU33/432x modules.
Details wiring and resistance measurements for SHU303x/313x modules.
Shows circulation pump resistance measurements for various models.
Provides circulation pump resistance measurements for SHU995x/SHV68.
Displays the wiring diagram for SHU 30 dishwasher models.
Shows the wiring diagram for SHU 303X/313X dishwasher models.
Displays the wiring diagram for SHU 40 dishwasher models.
Shows wiring diagrams for SHU 43C and SHU 53A dishwasher models.
Displays wiring diagrams for SHU 43E, SHU 53E, and SHU 66E models.
Shows wiring diagrams for SHU 33 and SHU 4322/4326 models.
Displays wiring diagrams for SHI 43/68 and SHU 43/53/68 models.
Shows wiring diagrams for SHI/SHU 43 models.
Displays wiring diagram for SHU 53 models.
Shows wiring diagrams for SHU 88/99 and SHV 43/48 models.
Displays wiring diagram for SHU 995X models.
Shows wiring diagram for SHV 68 models.
Displays wiring diagrams for SHU 66C and SHI 66A models.
Shows wiring diagrams for SHX and SHV models.
Displays wiring diagrams for SHY and SHV models.
Shows wiring diagrams for SHY, SHV, and SHX models.
General| Type | Built-in |
|---|---|
| Model | SHU9906 |
| Capacity | 14 place settings |
| Child Lock | Yes |
| Noise Level | 42 dBA |
| Wash Programs | 6 |
| Drying System | Condensation |
| Delay Start | Yes |
