To Next PageTo Next Page
Need help?Do you have a question about the Bosch SHU9922 and is the answer not in the manual?
Explanation of warning symbols used in instructions, indicating serious warnings for injury or damage.
Identifies potential hazards associated with dishwashers, such as electrical shock and sharp edges.
Advises to disconnect power before working on dishwashers and ensure proper grounding.
Warns about property damage from improper water connections, especially overtightening fittings.
States that no PC boards are handled in dishwasher repair as they are in plastic housings.
Confirms that no CFCs or refrigerants are used in dishwashers.
States there are no emissions from dishwashers; smells may come from drain connections.
Confirms that no carbon monoxide is emitted by dishwashers.
States there are no government compliance issues.
Details UL certification, Energy Star status, and NSF sanitization cycles.
Provides electrical, water pressure, and motor specifications for the dishwashers.
Explains how model numbers were changed and the meaning of each part in current and older models.
Shows the location of the serial label on the inner door and explains serial number formats.
Indicates that wiring and circuit diagrams are folded and located in a slot.
Details the limited lifetime warranty for Bosch dishwashers, including various coverage periods.
Refers to attached installation instructions for location requirements.
Refers to attached installation instructions for electrical requirements.
Refers to attached installation instructions for water and drain requirements.
Refers to attached installation instructions for shipping and packaging removal.
Covers leveling, handle installation, door reversal, and quick test procedures.
Explains how Bosch dishwashers use circulation/drain pumps, flow-through heaters, and NTC sensors.
Details components like circulation pump, drain pump, impeller, flow-through heater, NTC, and timers.
Explains how the wax motor operates the dispenser for detergent and rinse-aid.
Describes the top rack only feature with separate actuators and magnetic plungers.
Explains mechanical vs. electronic door switches and their activation by latches.
Details how aqua sensors affect energy usage by eliminating cycles if water is clean.
Explains how water fill assemblies ensure proper filling at various incoming pressures.
Describes how to access and remove water valves by removing the toe kick.
Details the steps to access circulation pumps by removing panels and blocking the tank.
Explains how to remove control modules by bending console tabs and disconnecting wires.
Describes how to access heaters and NTCs by removing the base or side panels.
Explains how to remove and install drain pumps by accessing them from the front.
Details the process for removing and installing dispensers, including precautions for sharp edges.
Describes how to disassemble and reassemble door latches for integrated models.
Explains how to access the aqua sensor from the left side of the dishwasher.
Describes how to access the water fill assembly by removing the left side panel.
Provides instructions for entering and using test programs to diagnose dishwasher issues.
Lists and explains test program error codes and customer use error codes for digital displays.
Guides on using test programs to measure heater and NTC resistance for diagnostics.
Troubleshooting table for common problems like washability, suds, odor, and indicator lights.
Discusses common issues related to specific parts like water valves, pumps, and control modules.
Troubleshooting flowchart for control modules showing a '1' error, indicating a heating problem.
Flowchart for diagnosing heater circuit failures by measuring current, voltage, and resistance.
Troubleshooting guide for water leaks past dishwasher doors, often related to condensation tubes.
Explains how to check the PTC pump motor starter for proper operation and connections.
Addresses nuisance tripping of thermal motor protectors on pumps with water switches.
Provides instructions for loosening and replacing circulation pump impellers.
Details part number changes for circulation pumps due to the 'softer bearing' upgrade.
Lists part number changes for circulation pumps and motors for specific models.
Discusses heater relay failures on control module PC boards and replacement recommendations.
Explains using a front cover to replace broken buttons on specific control modules.
Guides on replacing older control modules with #481055 and the necessary pushbutton pad changes.
Provides guidance on replacing older UC/06 model heaters with available alternatives.
Explains motor-operated water switches in heater assemblies for flow control.
Details sump part improvements made to enhance draining performance and prevent jamming.
Provides instructions for replacing damaged or detached dispenser doors.
Describes top-load dispensers and how rinse-aid dosage is adjusted via controls.
Steps to realign misaligned door latches causing doors not to close properly.
Addresses issues from miswired door latches/harnesses, preventing operation and potentially damaging modules.
Information on larger terminal boxes with rear conduit exits included since September 2003.
Provides wiring diagram and resistance measurements for control modules on SHU43C/53A models.
Wiring diagram and resistance measurements for control modules on SHX33A/43E/46A/B, SHV46C models.
Wiring diagram and resistance measurements for control modules on SHU66C, SHI66A models.
Wiring diagram and resistance measurements for control modules on SHX56B, SHV66A, SHY56/66 models.
Wiring diagram and resistance measurements for control modules on SHV99, SHX99, SHY99 models.
Wiring diagram and resistance measurements for control modules on SHU/SHI43/53/68 models.
Wiring diagram and resistance measurements for control modules on SHU995X, SHV68 models.
Wiring diagram and resistance measurements for control modules on SHU88/99 and SHV43/48 models.
Wiring diagram and resistance measurements for control modules on SHU33/432x models.
Wiring diagram and resistance measurements for control modules on SHU303x/313x models.
Wiring diagram showing circulation pump resistances for various SHU/SHV models.
Wiring diagram showing circulation pump resistances for SHU995x, SHV68 models.
Explanation of warning symbols used in instructions, indicating serious warnings for injury or damage.
Identifies potential hazards associated with dishwashers, such as electrical shock and sharp edges.
Advises to disconnect power before working on dishwashers and ensure proper grounding.
Warns about property damage from improper water connections, especially overtightening fittings.
States that no PC boards are handled in dishwasher repair as they are in plastic housings.
Confirms that no CFCs or refrigerants are used in dishwashers.
States there are no emissions from dishwashers; smells may come from drain connections.
Confirms that no carbon monoxide is emitted by dishwashers.
States there are no government compliance issues.
Details UL certification, Energy Star status, and NSF sanitization cycles.
Provides electrical, water pressure, and motor specifications for the dishwashers.
Explains how model numbers were changed and the meaning of each part in current and older models.
Shows the location of the serial label on the inner door and explains serial number formats.
Indicates that wiring and circuit diagrams are folded and located in a slot.
Details the limited lifetime warranty for Bosch dishwashers, including various coverage periods.
Refers to attached installation instructions for location requirements.
Refers to attached installation instructions for electrical requirements.
Refers to attached installation instructions for water and drain requirements.
Refers to attached installation instructions for shipping and packaging removal.
Covers leveling, handle installation, door reversal, and quick test procedures.
Explains how Bosch dishwashers use circulation/drain pumps, flow-through heaters, and NTC sensors.
Details components like circulation pump, drain pump, impeller, flow-through heater, NTC, and timers.
Explains how the wax motor operates the dispenser for detergent and rinse-aid.
Describes the top rack only feature with separate actuators and magnetic plungers.
Explains mechanical vs. electronic door switches and their activation by latches.
Details how aqua sensors affect energy usage by eliminating cycles if water is clean.
Explains how water fill assemblies ensure proper filling at various incoming pressures.
Describes how to access and remove water valves by removing the toe kick.
Details the steps to access circulation pumps by removing panels and blocking the tank.
Explains how to remove control modules by bending console tabs and disconnecting wires.
Describes how to access heaters and NTCs by removing the base or side panels.
Explains how to remove and install drain pumps by accessing them from the front.
Details the process for removing and installing dispensers, including precautions for sharp edges.
Describes how to disassemble and reassemble door latches for integrated models.
Explains how to access the aqua sensor from the left side of the dishwasher.
Describes how to access the water fill assembly by removing the left side panel.
Provides instructions for entering and using test programs to diagnose dishwasher issues.
Lists and explains test program error codes and customer use error codes for digital displays.
Guides on using test programs to measure heater and NTC resistance for diagnostics.
Troubleshooting table for common problems like washability, suds, odor, and indicator lights.
Discusses common issues related to specific parts like water valves, pumps, and control modules.
Troubleshooting flowchart for control modules showing a '1' error, indicating a heating problem.
Flowchart for diagnosing heater circuit failures by measuring current, voltage, and resistance.
Troubleshooting guide for water leaks past dishwasher doors, often related to condensation tubes.
Explains how to check the PTC pump motor starter for proper operation and connections.
Addresses nuisance tripping of thermal motor protectors on pumps with water switches.
Provides instructions for loosening and replacing circulation pump impellers.
Details part number changes for circulation pumps due to the 'softer bearing' upgrade.
Lists part number changes for circulation pumps and motors for specific models.
Discusses heater relay failures on control module PC boards and replacement recommendations.
Explains using a front cover to replace broken buttons on specific control modules.
Guides on replacing older control modules with #481055 and the necessary pushbutton pad changes.
Provides guidance on replacing older UC/06 model heaters with available alternatives.
Explains motor-operated water switches in heater assemblies for flow control.
Details sump part improvements made to enhance draining performance and prevent jamming.
Provides instructions for replacing damaged or detached dispenser doors.
Describes top-load dispensers and how rinse-aid dosage is adjusted via controls.
Steps to realign misaligned door latches causing doors not to close properly.
Addresses issues from miswired door latches/harnesses, preventing operation and potentially damaging modules.
Information on larger terminal boxes with rear conduit exits included since September 2003.
Provides wiring diagram and resistance measurements for control modules on SHU43C/53A models.
Wiring diagram and resistance measurements for control modules on SHX33A/43E/46A/B, SHV46C models.
Wiring diagram and resistance measurements for control modules on SHU66C, SHI66A models.
Wiring diagram and resistance measurements for control modules on SHX56B, SHV66A, SHY56/66 models.
Wiring diagram and resistance measurements for control modules on SHV99, SHX99, SHY99 models.
Wiring diagram and resistance measurements for control modules on SHU/SHI43/53/68 models.
Wiring diagram and resistance measurements for control modules on SHU995X, SHV68 models.
Wiring diagram and resistance measurements for control modules on SHU88/99 and SHV43/48 models.
Wiring diagram and resistance measurements for control modules on SHU33/432x models.
Wiring diagram and resistance measurements for control modules on SHU303x/313x models.
Wiring diagram showing circulation pump resistances for various SHU/SHV models.
Wiring diagram showing circulation pump resistances for SHU995x, SHV68 models.
General| Brand | Bosch |
|---|---|
| Model | SHU9922 |
| Category | Dishwasher |
| Language | English |
