How to prevent scalding from Bosch TSS when temperatures are too high?
To prevent scalding when your Bosch Solar panel system reaches temperatures higher than 60°C, install a mixing device and set the temperature limit to 60°C.
What to do if Bosch TSS collectors are in the shade?
If your Bosch Solar panel collectors are in the shade, remove the source of shading to allow for optimal sunlight exposure.
How to fix leaks at the collector connection of Bosch Solar panel?
If you notice leaks at the collector connection of your Bosch Solar panel, it may be due to the hose clip being mounted incorrectly or not secured. Ensure the hose clip is correctly positioned over the bead of the collector connection and tighten the circlip.
How to reduce heat loss from the pipework of a Bosch Solar panel?
To resolve excessive heat losses at the pipework of your Bosch Solar panel, position the system so that the pipework/cables are as short as possible. Additionally, install sufficient insulation on the DHW line to the consumer.
How to clean a heavily soiled Bosch TSS?
If your Bosch Solar panel collector panel is heavily soiled, clean the panels with water when the sun is not shining. Avoid using acetone or glass cleaner.
What to do if Bosch TSS Solar panel pressure relief valve is discharging water?
If you experience potable water discharge from the pressure relief valve of your Bosch Solar panel, install an on-site expansion vessel on the cold water connection and systematically remove any water leaks.
How to correct the orientation of a Bosch Solar panel collector?
To correct an incorrectly oriented Bosch Solar panel collector, align the collectors to face the midday sun for optimal solar capture.
Why is the Bosch TSS immersion heater not working?
If the immersion heater (accessory) for your Bosch Solar panel is not working, check the cables to ensure they are correctly connected. Also, verify that the thermostat has been inserted far enough (contacts must not be bent), check whether the high limit safety cut-out on the thermostat has been triggered, ensure the set temperature at the thermostat is high enough (see scale), and measure the resistance of the heating element. If it has short-circuited, replace the heating element.
How to fix leaks at the cylinder connections of a Bosch TSS Solar panel?
If you discover leaks at the cylinder connections of your Bosch Solar panel, check whether seals have been installed and whether these seals are damaged. Only screw on connector pipes hand tight then turn again through ½ revolution (corresponds to roughly 35 Nm).
What to do if the pipework is swapped around on a Bosch TSS Solar panel?
If your Bosch Solar panel system's pipework has been swapped around, check the pipework to ensure it is correctly configured.
Defines signal words and symbols used for warnings and information.
Provides crucial safety information, intended use, and warnings for installation and operation.
Warning about potential damage to immersion heater if storage tank is not filled.
Instructions for explaining system operation, safety, and maintenance to the user.
Lists all components included in the WSF and MTSS installation sets for flat roof frames.
Details energy consumption data for different system configurations.
Presents calculated annual results for solar coverage and system performance.
Provides recommendations for selecting the thermosiphon system based on daily DHW consumption.
Lists technical specifications for collectors and the entire thermosiphon system.
Defines the system's intended purpose and limitations, including installation angle and load capacity.
Offers tips for optimizing energy savings and efficient operation of the solar system.
States conformity with European Directives and national requirements.
Outlines applicable standards for rooftop installation and thermal solar systems.
Specifies technical rules for the installation of hot water storage heaters.
Provides general guidance, including safety precautions and site assessment for installation.
Explains how to determine necessary clearances for roof structures and collectors.
Lists the specific tools needed for installing the WSF and MTSS connection sets.
Warns about the dangers of falling from the roof during transport and installation.
Provides instructions and safety warnings for safely transporting collectors.
Details how to safely transport the storage tank to the installation location.
Explains the process of installing angle profiles for the WSF flat roof frame.
Describes how to fit flat profiles to form the frame structure.
Guides the installation of profile rails, including anti-slip protectors.
Covers the installation of accessories for increasing the system's load-bearing capacity.
Details methods for creating a secure roof connection using base anchors or ballast troughs.
Explains how to assemble and install the wind cross structure.
Guides the assembly of angle profiles for systems with two collectors.
Describes how to fit the upper clamps for collector installation.
Details the installation of the base bracket and lower clamps.
Covers safety precautions and preparation steps before installing collectors.
Provides step-by-step instructions for installing WSF collectors on the frame.
Offers instructions for installing MTSS collectors on the frame.
Details how to create the base anchor for collectors on different roof types.
Guides the placement and alignment of the storage tank on the flat roof frame.
Explains how to connect the flow pipe from the collector to the system.
Details the process of connecting the return pipe.
Covers connecting the potable water inlet, pressure relief valve, and expansion vessel.
Explains when lightning protection is required and how to implement it.
Provides instructions for safely filling the potable water circuit.
Guides the process of filling the solar circuit with heat transfer medium.
Discusses the company's commitment to environmental protection and disposal of components.
Provides instructions for safely shutting down and draining the system.
Outlines the schedule and tasks for regular system maintenance and inspection.
Details how to clean the collector glass panes and vents.
Explains how to manually check the function of pressure relief valves.
Guides the process of checking the magnesium anode's condition and replacement.
General| Brand | Bosch |
|---|---|
| Model | TSS Series |
| Category | Solar panel |
| Language | English |
To Next Page
