How to prevent scalding from Bosch TSS300-2E/FCC-2 when temperatures are too high?
To prevent scalding when your Bosch Solar panel system reaches temperatures higher than 60°C, install a mixing device and set the temperature limit to 60°C.
What to do if Bosch TSS300-2E/FCC-2 collectors are in the shade?
If your Bosch Solar panel collectors are in the shade, remove the source of shading to allow for optimal sunlight exposure.
How to fix leaks at the collector connection of Bosch Solar panel?
If you notice leaks at the collector connection of your Bosch Solar panel, it may be due to the hose clip being mounted incorrectly or not secured. Ensure the hose clip is correctly positioned over the bead of the collector connection and tighten the circlip.
How to reduce heat loss from the pipework of a Bosch TSS300-2E/FCC-2 Solar panel?
To resolve excessive heat losses at the pipework of your Bosch Solar panel, position the system so that the pipework/cables are as short as possible. Additionally, install sufficient insulation on the DHW line to the consumer.
How to clean a heavily soiled Bosch Solar panel?
If your Bosch Solar panel collector panel is heavily soiled, clean the panels with water when the sun is not shining. Avoid using acetone or glass cleaner.
What to do if Bosch TSS300-2E/FCC-2 Solar panel pressure relief valve is discharging water?
If you experience potable water discharge from the pressure relief valve of your Bosch Solar panel, install an on-site expansion vessel on the cold water connection and systematically remove any water leaks.
How to correct the orientation of a Bosch Solar panel collector?
To correct an incorrectly oriented Bosch Solar panel collector, align the collectors to face the midday sun for optimal solar capture.
Why is the Bosch TSS300-2E/FCC-2 Solar panel immersion heater not working?
If the immersion heater (accessory) for your Bosch Solar panel is not working, check the cables to ensure they are correctly connected. Also, verify that the thermostat has been inserted far enough (contacts must not be bent), check whether the high limit safety cut-out on the thermostat has been triggered, ensure the set temperature at the thermostat is high enough (see scale), and measure the resistance of the heating element. If it has short-circuited, replace the heating element.
How to fix leaks at the cylinder connections of a Bosch TSS300-2E/FCC-2?
If you discover leaks at the cylinder connections of your Bosch Solar panel, check whether seals have been installed and whether these seals are damaged. Only screw on connector pipes hand tight then turn again through ½ revolution (corresponds to roughly 35 Nm).
What to do if the pipework is swapped around on a Bosch TSS300-2E/FCC-2 Solar panel?
If your Bosch Solar panel system's pipework has been swapped around, check the pipework to ensure it is correctly configured.
Covers target group, intended use, and general safety precautions for installation.
Technical specifications for collectors and the entire thermosiphon system.
Defines the system's purpose and limitations for installation.
Pre-installation advice, warnings, and roof condition checks.
Safety and procedures for transporting collectors, avoiding falling loads.
Steps for installing angle profiles, flat profiles, and profile rails.
Methods for roof connection and installing accessories for higher loads.
Covers angle profiles, upper clamps, and base brackets for MTSS.
Detailed steps for installing WSF collectors on the frame.
Detailed steps for installing MTSS collectors on the frame.
Warnings for working on the system: falling, loose components, electric shock.
General| Model | TSS300-2E/FCC-2 |
|---|---|
| Rated Power (Pmax) | 300 W |
| Open Circuit Voltage (Voc) | 45.8 V |
| Short Circuit Current (Isc) | 8.65 A |
| Maximum System Voltage | 1000 V |
| Temperature Coefficient of Pmax | -0.45 %/°C |
| Weight | 22.5 kg |
To Next Page
