12 | English
Safety Warnings for Drills
Safety instructions for all operations
u Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
u Use the auxiliary handle(s). Loss of control can cause
personal injury.
u Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting ac-
cessory or fasteners may contact hidden wiring or its
own cord. Cutting accessory or fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Safety instructions when using long drill bits
u Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
u Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
u Apply pressure only in direct line with the bit and do
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings
u Switch the power tool off immediately if the applica-
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
u Hold the power tool securely. When tightening and
loosening screws be prepared for temporarily high torque
reactions.
u Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
u Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
u Always wait until the power tool has come to a com-
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
u Hold the power tool firmly with both hands and make
sure you have a stable footing. The power tool can be
more securely guided with both hands.
u In order to prevent the power tool from being
switched on unintentionally, always unlock the lock-
on button. To do so, briefly press the On/Off switch.
u Application tools can become hot during operation.
There is a risk of burns when changing the application
tool. Use protective gloves to remove the application
tool.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for impact drilling in brick, con-
crete and stone, as well as for drilling in wood, metal,
ceramic and plastic. Tools with electronic control and clock-
wise/anticlockwise rotation are also suitable for screwdriv-
ing.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Keyless chuck
(2)
"Drilling/impact drilling" selector switch
(3)
Rotational direction switch
(4)
Lock-on button for on/off switch
(5)
On/off switch
(6)
Speed preselection thumbwheel
(7)
Wing bolt for auxiliary handle adjustment
a)
(8)
Auxiliary handle with depth stop
a)
(9)
Handle (insulated gripping surface)
(10)
Auxiliary handle (insulated gripping surface)
(11)
Button for depth stop adjustment
a)
(12)
Depth stop
a)
(13)
Universal bit holder
a)
(14)
Screwdriver bit
a)
1 609 92A 9ED | (29.02.2024) Bosch Power Tools
To Next Page
Loading...
