What to do if MIDI messages are not being transmitted or received by my Boss RC-300?
If MIDI messages aren't being transmitted or received, consider these solutions: * Replace the MIDI cable to rule out a short. * Check all connections to the external MIDI device. * Ensure the MIDI channels of both devices match. * If transmitting from the RC-300, verify the Program Change Message Transmit and Control Change Message Transmit settings.
What to do if I am unable to hear sounds from a device connected to AUX/INST/MIC jacks on my Boss RC-300 Music Pedal?
If you can't hear sounds from devices connected to the AUX/INST/MIC jacks, try these steps: * Adjust the INPUT LEVEL knobs for AUX, INS, and MIC to suitable positions. * Confirm that the “Input Output Select” setting is correct.
How to fix playback tempo not changing on my Boss RC-300?
If the playback tempo isn't changing, consider these points: * You cannot change the phrase memory tempo during recording or overdubbing. Adjust the tempo while the performance is stopped or being played back. * If Tempo Sync is not set to ON in a track, the playback speed will not change even if the phrase memory tempo is altered. Enable Tempo Sync in the track settings.
What does 'MIDI Error!' mean on my Boss RC-300 Music Pedal and how can I resolve it?
If you receive a 'MIDI Error!' message: * Check to make sure that no corrupt MIDI messages are being transmitted. * Reduce the number or size of MIDI messages transmitted to the RC-300.
Why can't I synchronize two RC-300 units via MIDI?
If you're having trouble synchronizing two RC-300 units via MIDI, check the following: * Ensure the assignment source “SYNC START/STOP” and assignment target are correctly configured. Specifically, on the slave unit, the assignment target for the assignment source 'SYNC START/STOP' should be set to 'ALL PLAY/STOP' or 'TR1–3 PLAY/STOP'. * Avoid changing the phrase memory tempo of the master unit during synchronized performance.
What to do if I get a 'Too Busy!' message on my Boss RC-300?
If you receive a 'Too Busy!' message, try the following: * Lower the performance tempo. * Save the current content to a phrase memory. * Reduce the number of adjustments or changes made with the RC-300’s knobs and pedals. * Reduce the number or size of MIDI messages transmitted to the RC-300. * Ensure that the phrase is not shorter than 1.5 seconds.
What does 'UnSupportFormat!' mean on my Boss RC-300 and how to resolve it?
If you see an 'UnSupportFormat!' message, check the format of the WAV file you are trying to use.
What to do if the volume of the instrument connected to AUX/ INST/MIC jacks is too low on my Boss Music Pedal?
If the volume level of the instrument connected to the AUX/INST/MIC jacks is too low, make sure you are not using a connection cable that contains a resistor. Use a connection cable that does not contain a resistor.
What to do if Phrase Memories are not switching on my Boss RC-300?
If phrase memories are not switching, it may be because you are not on the Play screen. With the RC-300, you cannot switch phrase memories while any screen other than the Play screen is displayed. Press the [EXIT] button to return to the Play screen.
What to do if I am unable to communicate with computer using my Boss RC-300 Music Pedal?
If you're unable to communicate with your computer, check the USB cable connection. If exchanging files via USB, ensure the USB Mode is set to “STORAGE”.
General| Bit rate | 16 bit |
|---|---|
| Best uses | Guitar |
| Sample rate | 44.1 kHz |
| Product type | Footswitch/controller |
| Product color | Red, Black |
| Sound effects | Yes |
| Output impedance | 2000 Ω |
| Rhythms quantity | 83 |
| Maximum recording time | 3 h |
| Sound effects quantity | - |
| Display type | LED |
| Power source type | AC |
Weight and Dimensions| Depth | 231 mm |
|---|---|
| Width | 536 mm |
| Height | 76 mm |
| Weight | 3900 g |
To Next Page
