Why does my Braun 5696 turn off with a fully charged battery?
If your Braun Electric Shaver turns off even with a fully charged battery, it's likely that the foil and cutter are worn, requiring more power than the motor can provide. To resolve this, renew the Foil & Cutter cassette and regularly oil the shaving system, especially after cleaning it with water.
What to do if cleaning does not start when pressing the start button on my Braun 5696?
If the cleaning cycle doesn't start when you press the start button on your Braun Electric Shaver, consider these possibilities: * The shaver might not be properly placed in the Clean&Renew station. Ensure the shaver's contacts align with the station's contacts. * The cleaning cartridge may not contain enough cleaning fluid. If the display lights red, insert a new cleaning cartridge. * The appliance could be in stand-by mode. Press the start button again.
What to do if cleaning doesn't start on my Braun 5696 Electric Shaver?
If your Braun Electric Shaver cleaning does not start when you press the start button, there are a few possible reasons. First, the shaver might not be placed properly in the Clean&Renew station; ensure the contacts of the shaver align with the contacts in the station. Second, the cleaning cartridge may not contain enough cleaning fluid, indicated by a red light on the display; insert a new cleaning cartridge. Third, the appliance might be in standby mode; press the start button again.
Why is my Braun 5696 Electric Shaver head damp?
If your Braun Electric Shaver head is damp, it could be due to a few reasons. The drying time after automatic cleaning might have been too short, so clean directly after shaving to allow enough time for drying. The drain of the Clean&Renew station could be clogged, so clean the drain with a wooden toothpick and regularly wipe the tub clean. Alternatively, the cleaning cartridge might have been used for quite a while, decreasing the ethanol/isopropanol proportion while increasing the oil proportion; remove residue with a cloth.
What to do if my Braun Electric Shaver head is damp?
A damp shaver head on your Braun Electric Shaver can occur for a few reasons: * Insufficient drying time after automatic cleaning. Try cleaning directly after shaving to allow more drying time. * A clogged Clean&Renew station drain. Clean the drain with a wooden toothpick and regularly wipe the tub clean. * Prolonged use of the cleaning cartridge. The ethanol/isopropanol proportion decreases while the oil proportion increases. Remove residue with a cloth.
Why is my Braun Electric Shaver cleaning fluid consumption increased?
Increased cleaning fluid consumption in your Braun Electric Shaver's Clean&Renew station is often due to a clogged drain. Try cleaning the drain with a wooden toothpick and regularly wipe the tub clean.
Why are battery segments skipped on my Braun 5696 Electric Shaver?
If the battery segments in the display of your Braun Electric Shaver are skipped as the battery capacity decreases, it's usually because the foil and cutter are worn, which increases the power needed for each shave. Replace the Foil & Cutter cassette and regularly oil the shaving system, especially if you clean it with water.
Why has my Braun 5696 Electric Shaver shaving performance dropped?
If the shaving performance of your Braun Electric Shaver has significantly decreased, several factors could be responsible. First, the foil and cutter may be worn and need replacement. Second, the personal setting for shaving performance might have been changed. For a thorough and fast shave, the green (intensive) setting is recommended. Third, the shaving system could be clogged. To resolve this, soak the Foil & Cutter cassette in hot water with a drop of dish liquid, then rinse it properly, tap it out, and apply a drop of light machine oil once it's dry.
Why has the battery performance of my Braun Electric Shaver dropped significantly?
If the battery performance of your Braun Electric Shaver has dropped significantly, it could be due to a couple of reasons. First, the foil and cutter may be worn, requiring more power for each shave. Second, the shaver head might be regularly cleaned with water but not lubricated. To fix this, renew the Foil & Cutter cassette. Also, if you regularly clean the shaver with water, apply a drop of light machine oil on top of the foil once a week for lubrication.
What to do if replacement symbol lights up after changing shaving parts on Braun 5696?
If the replacement symbol lights up on your Braun Electric Shaver even after changing the shaving parts, it means the reset button hasn't been pushed. Push the reset button for at least 3 seconds to reset the counter.
General| Model | 5696 |
|---|---|
| Wet & Dry | Yes |
| Charging Time | 1 hour |
| Corded Use | Yes |
| Precision Trimmer | Yes |
| AutoSensing Motor | Yes |
| Waterproof | Yes |
| Charging Stand | Yes |
| Travel Case | Yes |
| Battery Type | Li-Ion |
To Next Page
