BRAYER BR1102 - Initial Setup and Espresso Rules; Initial Setup and Preparation Steps; Choosing the Appropriate Cup; Rules for Making Espresso

8 9EN EN
• Unpack the co󰀨ee maker and remove all the packaging
materials.
• Keep the original package.
• Check the delivery set.
• Read the safety measures and operating
recommendations.
• Examine the co󰀨ee maker for damages, in case of
damage do not plug it into the mains.
• Make sure that the specications of power supply
voltage specied on the lower panel of the unit
correspond to the specications of your mains. When
the unit is used in the mains with 60 Hz frequency, it
does not need any additional settings.
• Wipe the surface of the co󰀨ee maker body with a clean,
slightly damp cloth to remove dust.
• Before using the co󰀨ee maker for the rst time, wash all
removable parts (1, 2, 9, 10, 14, 16, 18, 19, 20, 21) with
warm water and neutral detergent and dry them.
BEFORE USING THE UNIT
ATTENTION!
If you switch the co󰀨ee maker on and don’t perform
any actions, the co󰀨ee maker will switch o󰀨 in 15
minutes. To switch the co󰀨ee maker on press any
button (5, 7, 8).
• Place the co󰀨ee maker on a steady at heat-resistant
surface, the distance from the side walls of the co󰀨ee
maker should be at least 20 cm, and the gap above the
co󰀨ee maker should be at least 30 cm.
• Do not use the co󰀨ee maker under kitchen shelves of
cupboards. They can be damaged by the steam released
during the co󰀨ee maker operation.
• The co󰀨ee maker should be placed out of reach of small
children.
Attention! Before making co󰀨ee for the rst time it is
recommended to wash the broiler, the cappuccinator lid (14)
and the milk container (16).
• Make sure that the removable tray (1) and the tray grid
(2) are installed to their places.
• Remove the lid (9), remove the water tank (10).
• Fill the tank (10) with cold water up to the maximal level
mark, install the tank (10) back to its place.
Note: the tank (10) is intended for water only, do not ll the
tank (10) with other liquids, such as milk.
• Take the container (16), pull it towards yourself and
remove it, remove the cappuccinator lid (14) from the
container (16) (pic. 1). Fill the container with water up to
the maximal level mark.
Note: the cappuccinator container (16) is intended for milk
only, do not ll the container (16) with other liquids, use
water only in the cappuccinator lid (14) washing mode.
• Install the cappuccinator lid (14) on the container (16)
and install the cappuccinator back to its place until the
lock clicking.
Note: after installing the container (16) with the lid (14) back
to its place always check if it is installed and xed properly.
• Set the milk supply intensity control knob (15) to the
middle position.
• Install one of the co󰀨ee lters (19 or 20) into the lter
holder (18) matching the ledge on the lter (19 or 20)
with the hole on the holder (18) and turn the lter (19 or
20) counter/clockwise. Do not add ground co󰀨ee into
the lter (19 or 20) when preparing the co󰀨ee maker
for work.
• Install the lter holder (18) into the installation place «
» and turn the handle (4) to the right as far as it will
go « » (pic. 2, 3, 4).
• Place a cup of suitable height and capacity of at least
300 ml on the tray grid (2).
• Direct the cappuccinator pipe (13) into the cup using
the cappuccinator pipe angle adjustment bar (12).
• Insert the power plug into the mains socket.
• Switch the co󰀨ee maker on by setting the power switch
(11) «0/I» to the position «I», the indicator (6) will light
up and start ashing.
• When the co󰀨ee maker is ready for operation, the light
indicator (6) will glow constantly.
• To switch the cleaning mode on press the
«Cappuccino»-button (7) twice.
• After you nish cleaning the co󰀨ee maker, switch the
co󰀨ee maker o󰀨 by setting the switch (11) «0/I» to the
position «0».
• Pour the water out of the cup, take the container (16),
pull it towards yourself and remove (pic. 1), remove the
cappuccinator lid (14) from the container (16), pour the
remaining water from the container (16). Slightly lift the
front part of the tray (1) and remove it, pour the water
out of it and install the tray (1) back to its place.
• Turn the lter holder handle (4) to the left and remove it
(pic. 2, 3, 4). Wait until the lter holder (18) cools down
completely and remove the installed lter (19 or 20)
turning it counter/clockwise. Wash the lter (19 or 20)
and install it into the lter holder (18).
• If necessary, clean the boiler and the cappuccinator lid
(14) several times.
• After cleaning the co󰀨ee maker is ready for operation.
CHOOSING THE APPROPRIATE CUP
• Before making co󰀨ee, please, select a cup of
appropriate capacity according to the table:
Drink Estimated amount of the ready
drink
Espresso:
оne / double
60 ml/119 ml
Cappuccino:
оne / double
178 ml/355 ml
Latte:
one / double
296 ml/474 ml
RULES OF MAKING ESPRESSO
• Use fresh-ground co󰀨ee beans or ground co󰀨ee for
«espresso» co󰀨ee makers.
• Make even and slightly tamp the ground co󰀨ee in the
lter (19 or 20), you can do it with the back side of the
measuring spoon (21) (pic. 5, 6, 7).