Brewmatic LA-3 SERIES

Questions and Answers

R
rrobertsSep 23, 2025
How to adjust beverage level on Brewmatic LA-3 Coffee Maker?
- R
  Robert HessSep 23, 2025
  To adjust the beverage level on your Brewmatic Coffee Maker, adjust the timer. Turn the timer knob clockwise to increase the beverage level and counterclockwise to decrease it. Adjust by a maximum of 1/2 reference mark per adjustment, retesting as needed. Test the timer, and clean the flow control washer and screen. Ensure the flow control washer is .25 gpm with code “CCP”. Test the incoming water pressure, ensuring it's between 30-80 psi; install a regulator if it exceeds 80 psi.
D
Diane DanielsAug 23, 2025
Why does my Brewmatic LA-3 Coffee Maker trip the circuit breaker?
- M
  mia43Aug 25, 2025
  Your Brewmatic Coffee Maker might be tripping the circuit breaker because too many appliances are on the same circuit, or the circuit's amperage is too low. Try using a correctly rated circuit, which may require a dedicated wall circuit. An electrician can help correct this. Also, check the coffee maker's internal wiring for issues and inspect the warmer and immersion elements for damage, replacing them if needed.
U
ucarpenterAug 25, 2025
What to do if my Brewmatic LA-3 Coffee Maker will not brew coffee but heats up?
- B
  browndanielAug 26, 2025
  If your Brewmatic Coffee Maker heats but doesn't brew, press the start switch on automatic models to begin a brew cycle. For pour-over models, pour about 60 oz of water to start brewing. Check the reservoir and tubing for blockages. Make sure the internal wiring is correct. Inspect for loose, damaged, or overheating wires or terminals. Repair or replace wiring as necessary. Test the timer and start switch, replacing if needed (automatic models only). Clean the flow control, washer, and screen (automatic models only). Also, check any in-line water filters or shut-off valves for issues (automatic models only).
J
jamesellisAug 26, 2025
Why is my Brewmatic LA-3 Coffee Maker brewing cycle too slow?
- K
  Katie MooreAug 27, 2025
  If your Brewmatic Coffee Maker's brewing cycle is too slow, inspect and clean the spray head, silicone tubing, and siphon fittings. Avoid over-tightening the tank lid hold-down screw.
B
Brian GibsonAug 27, 2025
What to do if the hot water faucet drips constantly on my Brewmatic Coffee Maker?
- S
  Samuel GonzalezAug 27, 2025
  If the hot water faucet drips constantly on your Brewmatic Coffee Maker, inspect the faucet seat cup for cracks or hardening and replace if necessary. Also, check the faucet for hard water deposits, wear, or leaks; clean or replace the faucet as needed.
M
michael12Sep 17, 2025
Why do solenoid valve chatter on my Brewmatic LA-3?
- N
  nmunozSep 17, 2025
  If the solenoid valve chatters on your Brewmatic Coffee Maker, ensure it's connected to a cold water line only and that supply lines aren't touching the brewer or countertop. Water pressure should be between 30-80 psi; install a regulator if it exceeds 80 psi. If water hammer is the issue, contact a plumber.
P
Pamela PriceSep 14, 2025
How to adjust the hot water faucet flow on Brewmatic LA-3?
- M
  Michael WrightSep 14, 2025
  To adjust the hot water faucet flow on your Brewmatic Coffee Maker, use the faucet adjustment needle valve to achieve approximately 5 oz in 15-20 seconds. Turn counterclockwise to increase flow and clockwise to decrease. Adjusting beyond recommended settings may cause rapid cooling.
V
Valerie LunaSep 15, 2025
How to fix not hot enough water from the hot water faucet on Brewmatic LA-3 Coffee Maker?
- H
  hayesnathanSep 15, 2025
  If the water from the hot water faucet isn't hot enough on your Brewmatic Coffee Maker, ensure the faucet is correctly adjusted. The coffee brewer must be on and heated for the faucet to deliver hot water.
A
Alyssa RamosSep 6, 2025
What to do if there are coffee grounds in my Brewmatic brewed coffee?
- M
  Megan CookSep 6, 2025
  If there are coffee grounds in your brewed coffee from Brewmatic Coffee Maker, test the brew cycle for correct beverage level and adjust if needed (automatic models only). Inspect the brew cone for damage and ensure the correct spray head (stainless steel with 5 holes) is used. Adjust the amount and grind of coffee, and ensure you're using the correct paper filter, using only one per brew cycle.
C
Christy IbarraSep 3, 2025
Why is the beverage level inconsistent on my Brewmatic LA-3 Coffee Maker?
- G
  Gregory MeadowsSep 3, 2025
  To address inconsistent beverage levels in your Brewmatic Coffee Maker, start by inspecting and cleaning the spray head, silicone tubing, and siphon fittings. Check the reservoir and tubing for blockages. Ensure the tank cover is correctly placed with good gaskets, and avoid overtightening the lid screw. Dry the timer if there's moisture (automatic models only). Test the incoming water supply for consistent pressure; install a regulator if needed. Test the timer, check in-line filters, and inspect faucet coil fittings and the solenoid valve for leaks, repairing or replacing parts as necessary (automatic models only).