Brewmatic 1033510 - User Manual

Questions and Answers

E
Eric FarmerSep 10, 2025
Why does my Brewmatic Coffee Maker start brewing automatically?
- T
  Teresa WilsonSep 10, 2025
  If your Brewmatic Coffee Maker starts brewing on its own, test and replace the “Power-Off-Fill “ Switch if necessary. Test the solenoid valve for leaks and replace it if necessary. Test and replace the timer if needed. Check the internal wiring for issues, and repair or replace as necessary. Test the incoming water supply pressure, ensuring it's between 30 and 80 psi; if over 80 psi, install a regulator to reduce it to 50 psi.
V
Victoria PaulAug 22, 2025
Why does my Brewmatic Coffee Maker keep tripping the breaker?
- K
  Karen WashingtonAug 23, 2025
  If your Brewmatic Coffee Maker is tripping the circuit breaker, it could be due to too many appliances on one circuit or a low amperage rating. Try using a correctly rated circuit, potentially a dedicated one, or consult an electrician. Verify the electrical specifications. Also, inspect the internal wiring for issues and check the tank heating element, replacing the tank if necessary.
J
Jason TurnerAug 25, 2025
What to do if my Brewmatic Coffee Maker won't brew but the light is on?
- C
  cuevasjeremyAug 25, 2025
  If your Brewmatic Coffee Maker light is on but it won't brew, test and replace the “Power-Off-Fill“ switch if necessary. Inspect, clean, or replace the flow washer and screen. Test and replace the thermostat if needed. Test the tank heating element, replacing the tank if necessary. Check the internal wiring for any issues, and repair or replace as needed. Also, check any in-line water filters, check valves, or shut-off valves for proper operation or blockages.
R
Richard ThompsonAug 26, 2025
Why is my Brewmatic Coffee Maker brewing cold coffee?
- M
  Michelle FloresAug 26, 2025
  If your Brewmatic Coffee Maker brews but the water stays cold, test and replace the thermostat if necessary. Also, check the internal wiring for any loose, damaged, or overheating wires or terminals, and repair or replace them as needed.
V
Valerie HolmesAug 27, 2025
Why won't my Brewmatic Coffee Maker start brewing?
- K
  Keith BlankenshipAug 28, 2025
  If the brewing cycle on your Brewmatic Coffee Maker doesn't start but the unit heats or steams, test and replace the thermostat if necessary. Inspect, clean, or replace the flow washer and screen. Test and replace the “Power-Off-Fill“ switch if needed. Test and replace the solenoid valve if necessary. Also, check any in-line water filters, check valves, or shut-off valves for proper operation or blockage. Check the internal wiring for issues, and repair or replace as needed.
K
kennedymarioAug 29, 2025
How to adjust the temperature on my Brewmatic Coffee Maker?
- J
  Jimmy HarrisAug 29, 2025
  If your Brewmatic Coffee Maker's brewing temperature is off, adjust or replace the thermostat, turning the adjustment screw counter-clockwise to increase the temperature and clockwise to decrease, making small adjustments (1/8 turn). The recommended temperature is between 192° and 196°F, tested below the brew cone with water only. Ensure the flow control washer is .06 gpm, as incorrect washers affect beverage levels. Also, check the incoming water supply pressure, which should be between 30 and 80 psi; if it exceeds 80 psi, install a regulator to reduce it to 50 psi.
S
Samantha GarciaSep 18, 2025
Why is my Brewmatic Coffee Maker leaking water from the bottom?
- J
  Julie HudsonSep 18, 2025
  If water is leaking from the bottom of your Brewmatic Coffee Maker, inspect the tank, silicone tubing, and fittings for leakage.
A
Aaron LarsonSep 12, 2025
Why is my Brewmatic Coffee Maker dripping after brewing?
- M
  morgankirbySep 12, 2025
  If water drips from the spray head of your Brewmatic Coffee Maker after it's turned off, inspect and clean the spray head, silicone tubing, and fittings. Test the solenoid valve for leakage. Also, test the incoming water supply pressure, which should be between 30 and 80 psi; if it exceeds 80 psi, install a water pressure regulator to reduce the pressure to 50 psi.
T
Tabitha CamposSep 8, 2025
Why does the water flow start and stop during the brew cycle of my Brewmatic Coffee Maker?
- J
  Jessica JohnsonSep 8, 2025
  If the water flow in your Brewmatic Coffee Maker starts and stops during the brew cycle, test and replace the “Power-Off-Fill “ Switch if necessary. Test and replace the solenoid Relay if needed. Test the “Power-Off-Fill” switch, replacing it if necessary.
W
wsanchezSep 5, 2025
Why is my Brewmatic Coffee Maker dispensing too much or too little coffee?
- K
  Kimberly MclaughlinSep 5, 2025
  If the beverage level from your Brewmatic Coffee Maker is consistently too high or too low, inspect and clean the spray head, silicone tubing, and fittings. Test and replace the timer if necessary. Inspect, clean, or replace the flow washer and screen. Test the incoming water supply pressure, which should be between 30 and 80 psi; if it exceeds 80 psi, install a water pressure regulator to reduce it to 50 psi.