Briggs & Stratton 190707 User Manual (English)

To Next Page

Briggs

Stratfon

OPERATING

AND

MAINTENANCE

INSTRUCTIONS

MODELS

190700

190707

191700 to 191707

IIM THE INTEREST OF SAFETY, DO NOT RUN ENGINE AT EXCESSIVE SPEEDS

Operating

engine

excessive speeds increases

the

hazard

personal injury.

DO NOT

TAMPER WITH PARTS WHICH WlAY

INCREASE

THE

GOVERNED SPEED.

For rotary lawnmower safety,

USA

Standard Safety Specifications

for

Power Lawn Mowers specify

maximuin blade

tip

speed

of 19,000 feet

per

minute, primarily

reduce

the

hazard from thrown objects.

Rotary lawnmower manufacturers select

the

governed

top

speed

of the

engine based

on the

length

and

design

of the

cutter

blade

and

design

other mower parts.

All rotary lawnmowers should

checked

for

conformance

to the USA

Standard Safety Specifications

for

Power Lawn Mowers

on blade

tip

speed,

if the

engine

repaired

replaced,

or if

mower parts

are

changed.

Dirt

and

grass clippings,

other debris,

cooling fins

governor parts

can

affect engine speed.

See

cleaning instruc-

tions

Section

CAUTION

TO PREVENT ACCIDENTAL STARTING always remove

the

spark plug before working

on the

engine

equipment driven

by the

engine

remove cable from spark plug

and

insert terminal

V-notch

cylinder head cover.

NOT RUN THE

ENGINE

IN AN

ENCLOSED AREA. Exhaust gases contain carbon monoxide,

odorless

and

deadly poison.

NOT

FILL GASOLINE TANK WHILE ENGINE

RUNNING. Spilling gasoline

on a hot

engine

may

cause

fire

explosion.

Section

BEFORE STARTING

FILL SUMP WITH OIL - Use a high quality deter-

gent oil classified "For Service SC or SD or MS".

Nothing should be added to the recommended oil.

SUMMER

(Above

40° F.)

Use SAE

not

available.

Use

SAE

10W-30

SAE 10W-40

WINTER

(Under

40° F.)

Use SAE5W-20

or SAE

5W-30

not

available.

Use

SAE 10W or SAE

10W-30

Below

0° F,

Use

SAE 10W or SAE

10W-30

Diluted

10%

with Kerosene

DIRECTIONS: Place the engine level. Remove cap and

dipstick and fill to full mark on dipstick. When check-

ing oil level push dipstick assembly firmly but slowly

until cap bottoms on tube. Do not overfill. Dipstick

assembly must be pushed fully into tube at all times

when engine is operating. For engines not equipped

with extended oil

fill,

FILL THE OIL SUMP TO OVER-

FLOWING. Pour slowly. Capacity 2-1/4 pints.

FILL FUEL TANK - Use clean, fresh, lead-free or

leaded "regular" grade automotive gasoline. Fill

tank completely I

LOOK

FOR

MODEL,

TYPE

rMi

CI ,

NUMBERS

OIL FILL HERE

DO NOT MIX OIL WITH GASOLINE.

FORM NO.270676-62

PRINTED IN

U.S.A.

BRIGGS

STRATTON CORP.

Milwaukee, Wisconsin 53201

Other manuals for Briggs & Stratton 190707

Service Manual35 pages

Need help?

Do you have a question about the Briggs & Stratton 190707 and is the answer not in the manual?

Briggs & Stratton 190707 Specifications

General

Displacement	208 cc
Bore	68 mm
Power Output	6.5 hp
Fuel Type	Gasoline
Starting System	Recoil
Governor Type	Mechanical
Lubrication System	Splash
Fuel Shutoff	Yes
Oil Alert	Yes
Oil Capacity	20 oz
Dry Weight	48 lbs
Spark Plug	RC12YC
Carburetor	Float type
Air Cleaner	Dual-element
Rotation	Counterclockwise
Engine Type	4-stroke, single cylinder, OHV (Overhead Valve)