Briggs & Stratton BSPP 1950 PSI User Manual (English)

Questions and Answers:

A
Alexis NguyenAug 10, 2025
How to fix Briggs & Stratton Pressure Washer pump failure to produce pressure?
- M
  Melissa PalmerAug 10, 2025
  To address a failure to produce pressure in your Briggs & Stratton Pressure Washer pump, you can try the following steps: pull the nozzle backward for high pressure mode, clear the inlet, ensure adequate water flow, straighten the inlet hose and repair any leaks, check and clean the inlet hose strainer, use a cooler water supply, clear any blockages in the outlet hose, replace the gun if necessary, and clean the orifice. If these steps don't resolve the issue, contact a Briggs & Stratton Power Products service facility.
S
Sabrina CarlsonAug 15, 2025
What to do if Briggs & Stratton BSPP 1950 PSI Pressure Washer pump has erratic pressure?
- E
  Emily SmithAug 15, 2025
  If your Briggs & Stratton Pressure Washer pump is experiencing erratic pressure, try these solutions: pull the nozzle backward for high pressure mode, clear the inlet, ensure adequate water flow, straighten the inlet hose and patch any leaks, check and clean the inlet hose strainer, use a cooler water supply, clear blockages in the outlet hose, replace the gun, and clean the orifice. If the problem continues, contact a Briggs & Stratton Power Products service facility.
E
emendezAug 20, 2025
Why is detergent not mixing with the spray on my Briggs & Stratton Pressure Washer?
- R
  randy70Aug 20, 2025
  If the detergent is not mixing with the spray on your Briggs & Stratton Pressure Washer, make sure the detergent siphoning tube is inserted into the detergent. Then, clean or replace the filter/detergent siphoning tube. You can also check the in-line filter. Finally, push the nozzle forward for low pressure mode.
R
Raymond GallowayAug 25, 2025
Why does my Briggs & Stratton BSPP 1950 PSI have a loss of pressure?
- B
  brianknightAug 26, 2025
  If your Briggs & Stratton Pressure Washer pump has a loss of pressure, try the following: pull the nozzle backward for high pressure mode, clear the inlet, provide adequate water flow, straighten the inlet hose and patch any leaks, check and clean the inlet hose strainer, provide a cooler water supply, clear any blockages in the outlet hose, replace the gun, and clean the orifice. If the problem persists, contact a Briggs & Stratton Power Products service facility.
S
Shirley MartinezAug 29, 2025
Why is the water volume low on my Briggs & Stratton Pressure Washer?
- S
  Sandra James MDAug 30, 2025
  If you're experiencing low water volume with your Briggs & Stratton Pressure Washer, try these steps: pull the nozzle backward for high pressure mode, clear the inlet, ensure adequate water flow, straighten the inlet hose and patch any leaks, check and clean the inlet hose strainer, provide a cooler water supply, clear any blockages in the outlet hose, replace the gun if needed and clean the orifice. If the issue persists, contact a Briggs & Stratton Power Products service facility.
L
Larry AdamsSep 3, 2025
Why does my Briggs & Stratton Pressure Washer engine bog down under load?
- M
  michael84Sep 3, 2025
  If your Briggs & Stratton Pressure Washer engine runs well at no-load but bogs down when a load is added, it could be due to the engine speed being too slow. Try moving the throttle control to the FAST position. If the engine continues to bog down, contact the engine manufacturer for further assistance.